Onkyo TX-DS797 Owner Manual - Page 20

Connecting a subwoofer, Connecting the speaker cable, Connecting speakers - 5 1 channel receiver

Get Onkyo TX-DS797 PDF manuals and user guides View all Onkyo TX-DS797 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Connecting speakers Connecting speakers Caution: Connect only speakers with an impedance between 4 and 16 Ω to the TX-DS797. If the impedance of even one speaker is between 4 and 6 Ω, be sure to set the speaker impedance setting accordingly (see page 28). Notes: • When you are using only one speaker or when you wish to listen to monaural (mono) sound, a single speaker should never be connected in parallel to both the right and left-channel terminals simultaneously. Connecting the speaker cable 1. Strip away 5/8 inch (15 mm) of wire insulation. 2. Twist wire ends very tight. 3. Unscrew 4. Insert wire 5. Screw 1 15mm 2 SPEAKERS -+ L L SPEAKERS -+ L L 3 4 5 R - R + • To prevent damage to circuitry, never short-circuit the positive (+) and negative (-) speaker wire. NO! R - R + • Be sure to connect the positive and negative cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural. • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage the TX-DS797. • Connect your surround back speaker to the SURR BACK SPEAKER terminals (see page 20). Connecting a subwoofer Use the PRE OUT SUBWOOFER jack to connect a subwoofer with a built-in power amplifier. If your subwoofer does not have a built-in amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack and the subwoofer to the amplifier. Front right speaker Front left speaker Surround right speaker Surround left speaker DIGITAL OUTPUT OPT PRE OUT R L FRONT DIGITAL INPUT COAX 1 SUB SURR CENTER SURR BACK 2 ANTENNA AM FM 75 3 OPT 1 FRONT SUB MULTI CH INPUT AUDIO R L CENTER PH 2 3 DIGITAL INPUT SURR SURR BACK R GND CD OUT L TAPE IN R L AUDIO AUDIO R L VIDEO S VIDEO MONITOR OUT OUT ZONE 2 IN DVD OUT IN VIDEO 1 OUT IN VIDEO 2 IN VIDEO 3 AUDIO IN VIDEO 4 VIDEO S VIDEO COMPONENT VIDEO OUTPUT Y PB PR INPUT 1 Y PB PR INPUT 2 Y PB PR CAUTION: SPEAKER IMPEDANCE 4 OHMS MIN. OR 6 OHMS MIN. / SPEAKER SEE INSTRUCTION MANUAL FOR CORRECT SETTINGS. FRONT SPEAKERS R L SURR SPEAKERS R L AC OUTLETS AC 120V 60 Hz SWITCHED TOTAL 120W 1A MAX. CENTER SPEAKER I R IN SURR BACK SPEAKER 12V TRIGGER ZONE 2 OUT REMOTE CONTROL AV RECEIVER MODEL NO. TX-DS 797 Subwoofer Center speaker Surround Back speaker 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
20
Connecting a subwoofer
Use the PRE OUT SUBWOOFER jack to connect a subwoofer with
a built-in power amplifier. If your subwoofer does not have a built-in
amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack
and the subwoofer to the amplifier.
Connecting the speaker cable
1.
Strip away 5/8 inch (15 mm) of wire insulation.
2.
Twist wire ends very tight.
3.
Unscrew
4.
Insert wire
5.
Screw
Front left
speaker
Front right
speaker
Surround left
speaker
Surround right
speaker
Connecting speakers
Center
speaker
Subwoofer
•
Be sure to connect the positive and negative cables for the
speakers properly. If they are mixed up, the left and right signals
will be reversed and the audio will sound unnatural.
•
Do not connect more than one speaker cable to one speaker
terminal. Doing so may damage the TX-DS797.
•
Connect your surround back speaker to the SURR BACK
SPEAKER terminals (see page 20).
Connecting speakers
Caution:
Connect only speakers with an impedance between 4 and 16
Ω
to
the TX-DS797. If the impedance of even one speaker is between 4
and 6
Ω
, be sure to set the speaker impedance setting
accordingly (see page 28).
•
To prevent damage to circuitry,
never short-circuit the positive (+)
and negative (
–
) speaker wire.
NO!
Surround
Back
speaker
PRE OUT
ANTENNA
FRONT
SUB
SURR
SURR
BACK
CENTER
R
L
AUDIO
R
L
PH
CD
OUT
IN
TAPE
R
L
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
OUT
IN
OUT
IN
OUT
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
AUDIO
VIDEO
S VIDEO
COMPONENT
VIDEO
Y
P
B
P
R
OUTPUT
INPUT 1
Y
P
B
P
R
INPUT 2
Y
P
B
P
R
L
R
L
R
AC OUTLETS
AC
120
V
60
Hz
SWITCHED
TOTAL
120W
1A
MAX.
I
R
IN
OUT
12V TRIGGER
ZONE 2
REMOTE
CONTROL
AV RECEIVER
MODEL NO.
TX-DS
797
GND
AM
4 OHMS
MIN. OR
6 OHMS
MIN.
/SPEAKER
SEE
INSTRUCTION
MANUAL FOR
CORRECT
SETTINGS.
CAUTION
:
SPEAKER
IMPEDANCE
FM
75
DIGITAL
OUTPUT
DIGITAL
INPUT
OPT
COAX
2
3
1
2
3
1
OPT
DIGITAL
INPUT
FRONT SPEAKERS
SURR SPEAKERS
CENTER
SPEAKER
SURR
BACK
SPEAKER
R
L
MULTI
CH
INPUT
FRONT
SUB
SURR
SURR
BACK
CENTER
15mm
1
3
4
5
2
Notes:
•
When you are using only one speaker or when you wish to listen to
monaural (mono) sound, a single speaker should never be
connected in parallel to both the right and left-channel terminals
simultaneously.
R
L
R
L
SPEAKERS
+
–
+
–
R
L
R
L
SPEAKERS
+
–
+
–