Onkyo TX-DS797 Owner Manual - Page 51

Enjoying music or videos with the TX-DS797 Listening mode buttons DIRECT / SETUP ENTER STANDBY/ON STANDBY POWER ON OFF UPSAMPLING DISPLAY DIMMER DIRECT STEREO SURROUND THX DSP REC OUT ZONE 2 OFF TUNI NG SETUP ENTER PRESET RE TURN FM MODE MEMORY CLEAR A-FORM LISTENING MODE MEMORY PHONES AUDIO SELECTOR ZONE 2 (GRN ) REC ( RED ) DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VCR 1 VCR 2 TAPE FM AM PHONO C D DIGITAL MASTER VOLUME VIDEO 5/VIDEO CAM INPUT S VIDEO VIDEO L AUDIO R AV RECEIVER TX-DS797 Input source buttons / RETURN Listening mode buttons Changing the listening mode To change the listening mode during playback, press the listening mode buttons. The functions of the buttons on the TX-DS797 and those on the remote controller are the same. TX-DS797 DIRECT STEREO SURROUND THX DSP Remote controller If surround back speakers are not connected, you cannot select THX Surround EX, DTS-ES Discrete 6.1, or DTS-ES Matrix 6.1. DSP / : Changes the listening mode as shown below. Mono → Direct → Stereo → Theater-Dimensional → Surround* → THX* → Mono Movie → Enhanced 7 → Orchestra → Unplugged → Studio-Mix → TV Logic → All Ch Stereo → Mono. If pressed, the listening mode for the selected input source set in the Listening Mode Preset is also changed. * The display will differ depending on the format of the current signal. DIRECT: Changes the listening mode directly to the Direct listening mode. If pressed, the listening mode for the selected input source set in the Listening Mode Preset is also changed to the Direct listening mode. STEREO: Changes the listening mode directly to the Stereo listening mode. If pressed, the listening mode for the selected input source set in the Listening Mode Preset sub-menu is also changed to the Stereo listening mode. SURROUND (SURR): Changes the listening mode to the surround mode for the current input signal (e.g., Dolby Pro Logic II, Dolby Digital, or DTS). If pressed, the listening mode for the selected input source set in the Listening Mode Preset is also changed to the Surround listening mode. When the Surround listening mode is selected • When playing back DTS sources Switches the DTS-ES setting from Auto → On → Off. • When playing back Analog/PCM sources Switches from Pro Logic II Movie → Pro Logic II Music → DTS Neo6:Cinema → DTS Neo6:Music. • When playing back D.F. 2-channel sources Switches from Pro Logic II Movie → Pro Logic II Music. THX: Changes the listening mode to the THX listening mode. When the THX listening mode is selected • When playing back Dolby Digital sources Switches the THX Surround EX mode (Auto → On → Off) if the source is a Dolby Digital-compatible source. • When playing back Analog/PCM sources Switches the decoding mode (Pro Logic II Movie → DTS Neo6:Cinema) for THX processing. • When playing back DTS sources Allows you to enjoy the DTS THX Cinema, DTS-ES Discrete 6.1 THX Cinema, and DTS-ES Matrix 6.1 THX Cinema surround systems. The DTS-ES mode changes from Auto → On → Off. Entering names for input sources and tuner stations You can enter names for your components or radio station names as names for your input sources and have them displayed in the front panel display when that input source is selected. (see page 36) Entering characters using the TX-DS797: 1. Press the SETUP button. 2. Press the button to select the "2.Input Setup" menu and press the ENTER button. 3. Press the button to select the "Character Input?" sub- menu and press the ENTER button. 4. Press the button to select "Char: " and press the button. 5. The screen changes to show you the characters you have already entered (< >) and then automatically changes to the Character Selection screen (ABCDEF...). Press the , , , and buttons to select the character you desire and press the ENTER button. The screen again shows you the characters entered for approximately two seconds and returns you to the Character Selection screen. If you enter an incorrect character, press the RETURN button to move the cursor to the left and re-enter the character. Repeat the above operations to enter up to 10 characters. When you are finished, the entered name appears. 6. Press the SETUP button to complete the procedure. To correct entered characters Perform steps 1 to 4 given above. After performing step 4, press the button to display a name that has already been entered. Press the ENTER button to move the cursor to the location of the character that you want to change, enter the new character, and press the ENTER button. To delete an entered name Perform the steps 1 to 3 given above. At step 4, press the button. 51