Onkyo TX-NR646 Basics Guide - Page 12
En-12
View all Onkyo TX-NR646 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
¼¼The subwoofer sound may not be detected since it is extremely low frequencies. Set the subwoofer volume to around the half of its maximum volume and make its frequency to the maximum level. ¼¼Measurement may be interrupted if there is ambient noise or radio frequency interference. Close the window and turn off the home appliance and fluorescent light. 2. After placing the microphone at the measurement position, select "Do it Now" with the cursors and press ENTER. 3. When "Please plug microphone that came in a box with AV receiver" is displayed, connect the microphone to the SETUP MIC jack of the unit. SETUP MIC jack Calibration microphone 4. Select the settings for the connected speakers, the type of the height speakers, and other appropriate settings. AccuEQ Room Calibration Speaker Channels Subwoofer Height Speaker Bi-Amp Powered Zone2 7.1ch Yes ----No No Select how many speakers you have. ENTER Next When the screen above is displayed, set the items with the cursor buttons on the remote controller. Refer to the on-screen diagram for "Speaker Channels", which changes each time a different number of channels is selected. When all the items have been set, press ENTER on the remote controller. After that, follow the guidance displayed on the TV screen to operate the unit. ●● Refer to the content of an item, which appears on the lower left of the screen when the cursor is on the item. 5. The test tones sound from the connected speakers and automatic speaker setting starts. Measurement will be made 3 times or more for each speaker. It takes several minutes to be completed. Keep the room as quiet as possible during measurement. If any of the speakers do not produce the test tone, check for disconnection. ●● During measurement, each speaker outputs the test tones at a high volume. Be careful of sound leak that may disturb your neighbors, or be careful not to frighten young children. 6. When the measurement is completed, the measurement result is displayed. Press t/u on the remote controller to check the settings. Press ENTER with "Save" selected. Select "On" in the next screen and press ENTER on the remote controller. ●● You should normally select "On (All Channels)", and to disable just the front speakers, you should select "On (Except Front Left/Right)". ●● If there is an error message, follow the on-screen instruction to remove the error cause. 7. When "Please unplug setup microphone." is displayed, disconnect the microphone. 2 Source Connection You can check the connections on the different inputs and make HDMI link function settings. 1. When the Source Connection start screen is displayed, select "Yes, Continue" with the cursors and press ENTER. Initial Setup Source Connection ɹThis step will start to check if the ɹconnections were made correctly. ɹWould you like to continue? Yes. Continue No. Skip SETUP Exit 2. Select the desired input to check the connection and Step 2: Initial Setup press ENTER. Start playback of the selected device. If connection is correct, video/audio of the input source selected on the unit will be played. 3. After checking the connection, select "Yes" with the cursors and press ENTER. ●● If you select "No" and press ENTER, the error cause will be displayed. Follow the guidance to remove the error cause and check the connection again. 4. Select "Yes" with the cursors and press ENTER on the remote controller to check the connection of other inputs or select "No, Done Checking" and press ENTER to skip. If you select "Yes", you will return to the screen of step 2. If you select "No, Done Checking", you will proceed to step 5. 5. Set the CEC link function. Select "Yes" to enable the HDMI link function with CECcompliant equipment, then select "Yes" again in the next screen. Source Connection The following CEC-compatible devices are found; Do you wish to turn on the CEC link? xxxxxxxxxxx Yes No SETUP Exit If you select "Yes", the connection with ARC compatible TV and HDMI Standby Through function will be set to "On" and enabled. En-12