Onkyo TX-NR777 Owners Manual -Advanced - Page 24
> Before Start, > Part Names, > Install, > Playback, Advanced Manual, > Initial Setup
View all Onkyo TX-NR777 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Keep the room as quiet as possible during measurement. 0 If you have connected a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than halfway. 0 If the power of this unit suddenly turns off, the wires in the speaker cables may have touch the rear panel or other wires and tripped the protection circuit. Twist the wires again properly and make sure they do not stick out of the speaker terminals when connecting. 0 When using THX certified speakers, THX recommends setting the crossover frequency to "80Hz(THX)". It is also recommended to manually adjust the settings for each speaker to suit the specific characteristics of each room. 1. Place the supplied speaker setup microphone in the listening position, and connect to the SETUP MIC jack on the main unit. SETUP MIC When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place. 2. Select the connected speaker configuration. AccuEQ Room Calibration Speaker Channels 7.1 ch < > Subwoofer Yes Height Speaker --- Zone Speaker No Bi-Amp No Select how many speakers you have. Next The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings. 3. Test tones are emitted by the speakers, and firstly the unit detects the speakers connected and the noise in the environment. 4. After the results of the above measurements are displayed, select "Next", press ENTER on the remote controller, and the test tones are emitted again, and the unit automatically makes settings such as the optimum volume level and the crossover frequency. 5. When the measurement is completed, the measurement result is displayed. Press the cursors W / X on the remote controller to check the settings. Press ENTER when "Save" is selected to save the settings. 6. Select whether to enable or disable the equalizer function that corrects for distortion caused by the acoustic environment of the room. If this is to be enabled, then normally you should select "On (All Channels)", and to disable just the front speakers you should select "On (Except Front Left / Right)". 7. Disconnect the speaker setup microphone. ∫ 2. Source Connection Check that each input source is connected correctly. Follow the guidance, select the input you want to confirm, start play of the selected player, and confirm that the images appear on the TV and that sound is played. ∫ 3. Network Connection Set up Wi-Fi connection with an access point such as a wireless LAN router. There are the following two methods of connecting by Wi-Fi: "Scan Networks": Search for an access point from this unit. Find out the SSID of the access point beforehand. "Use iOS Device (iOS7 or later)": Share the iOS device's Wi-Fi settings with this unit. If you select "Scan Networks", there are a further two choices of connection method. Check the following. "Enter Password": Enter the password (or key) of the access point to connect. "Push Button": If the access point has an automatic connection button, you can connect without entering a password. 0 If the SSID of the access point is not displayed, then in the screen listing the SSIDs, select "Other..." with the X cursor on the remote controller and press ENTER, then follow the onscreen instructions. Keyboard Input To switch between upper and lower case, select "A/a" on the screen and press ENTER. To select whether to mask the password with "½" or display it in plain text, press MEMORY on the remote controller. Press CLEAR to delete all the input characters. 0 A confirmation screen asking you to agree to the privacy policy is displayed during network setting. Select "Accept" and press ENTER to indicate agreement. ∫ 4. Multi Zone Setup When you want to enjoy audio in a room other than the main room, set the audio output method for the separate room (ZONE 2). If you have connected speakers in a separate room with speaker cable, select "Using AV Receiver". If you have connected a pre-main amplifier in a separate room with an analog audio cable, select "with External Premain Amplifier". ∫ 5. Audio Return Channel If you have connected a TV that supports ARC, select "Yes". This unit's ARC setting turns on and you can listen to the TV's audio through this unit. 0 If you select "Yes", the HDMI CEC function is enabled and power consumption increases during standby. 24