Onkyo TX NR906 Owner Manual - Page 49

Connecting an RI Dock, Connecting the Power Cords of Other Components (North American model only)

Get Onkyo TX NR906 - AV Network Receiver PDF manuals and user guides
UPC - 751398008351
View all Onkyo TX NR906 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Connecting the AV Receiver-Continued Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock's instruction manual. ■ If Your iPod Supports Video: Connect your RI Dock's audio output jacks to the AV receiver's AUX 1 IN L/R jacks, and connect its video output jack to the AV receiver's AUX 1 IN V jack. (Onkyo DS-A2X hookup shown below.) ■ If Your iPod Doesn't Support Video: Connect your RI Dock's audio output jacks to the AV receiver's AUX 1 IN L/R jacks. (Onkyo DS-A2X hookup shown below.) IN L R V IN L R ■ If you have an Onkyo DS-A1 RI Dock • Connect its video output jack to the AV receiver's AUX 1 jack. Notes: • Connect the RI Dock to the AV receiver with an V cable (see page 50). • Set the RI Dock's RI MODE switch to "HDD" or "HDD/DOCK". • Set the AV receiver's Input Display to "DOCK" (see page 63). • By using the [CD] (TX-NR906) or [DOCK] (TX-SR876) REMOTE MODE button on the remote controller of the AV receiver to change the remote mode to "DOCK", you can operate your iPod in the RI Dock (see page 20). If you cannot operate it, you will need to enter the appropriate remote control code (see page 137). • See the RI Dock's instruction manual for more information. Connecting the Power Cords of Other Components (North American model only) The AV receiver has AC outlet on its rear panel that can be used to connect the power cords of other components that you intend to use with the AV receiver. These components can then be left turned on so that they turn on and off as and when the AV receiver is set to On or Standby. Caution: • Make sure that the total capacity of the components that you connect to the AC OUTLET does not exceed the stated capacity. Notes: • When the "HDMI Control" setting is set to "Enable" (page 118), the AC outlet are on all the time regardless of whether the AV receiver is set to On or Standby, or Ready mode in this case, so any components connected to them cannot be turned on or off automatically. • Onkyo components connected via V should be connected directly to a wall outlet, not an AC OUTLET on the AV receiver. AC OUTLET AC 120V 60Hz SWITCHED 120W 1A MAX. North American model 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
49
Connecting the AV Receiver
—Continued
■
If Your iPod Supports Video:
Connect your RI Dock’s audio output jacks to the
AV receiver’s AUX 1 IN L/R jacks, and connect its
video output jack to the AV receiver’s AUX 1 IN V
jack.
(Onkyo DS-A2X hookup shown below.)
■
If Your iPod Doesn’t Support Video:
Connect your RI Dock’s audio output jacks to the
AV receiver’s AUX 1 IN L/R jacks.
(Onkyo DS-A2X hookup shown below.)
■
If you have an Onkyo DS-A1 RI Dock
•
Connect its video output jack to the AV receiver’s AUX 1 jack.
The AV receiver has AC outlet on its rear panel that can be used to
connect the power cords of other components that you intend to use
with the AV receiver. These components can then be left turned on so
that they turn on and off as and when the AV receiver is set to On or
Standby.
Caution:
•
Make sure that the total capacity of the components that you con-
nect to the AC OUTLET does not exceed the stated capacity.
Notes:
•
When the “HDMI Control” setting is set to “Enable” (page 118),
the AC outlet are on all the time regardless of whether the AV
receiver is set to On or Standby, or Ready mode in this case, so any
components connected to them cannot be turned on or off automat-
ically.
•
Onkyo components connected via
u
should be connected
directly to a wall outlet, not an AC OUTLET on the AV receiver.
Connecting an RI Dock
Not all iPod models output video. For information
about which iPod models are supported by the RI
Dock, see the RI Dock’s instruction manual.
L
R
IN
V
L
R
IN
Notes:
•
Connect the RI Dock to the AV receiver with an
u
cable (see page 50).
•
Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.
•
Set the AV receiver’s Input Display to “DOCK” (see page 63).
•
By using the [CD] (TX-NR906) or [DOCK] (TX-SR876) REMOTE MODE button on the remote controller of
the AV receiver to change the remote mode to “DOCK”, you can operate your iPod in the RI Dock (see page 20).
If you cannot operate it, you will need to enter the appropriate remote control code (see page 137).
•
See the RI Dock’s instruction manual for more information.
Connecting the Power Cords of Other Components (North American model only)
AC OUTLET
AC 120V
SWITCHED
120W 1A MAX.
60Hz
North American model