Onkyo TX-RZ810 User Manual - Page 9

Step2: Connect the Speakers

Get Onkyo TX-RZ810 PDF manuals and user guides View all Onkyo TX-RZ810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

> Before start > Hookup > Setup > Playback > Part Names Step2: Connect the Speakers 1/2˝ (12 mm) 1 in case of: Pages 3 to 7 Connect 123456 for a 5.1-channel system. With a 7.1-Channel System (with Surround Back Speakers), also connect 7 and 8. With a 7.1-Channel System (with Height Speakers), connect 9:. Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER jacks. 0 You can also connect both 78 and 9:. However, you can only output audio from one set of 78 or 9: at a time. When you have connected both, you can select which speakers to prioritize with "Speaker Layout" (P26) in the Quick Menu. Setup 0 Settings for the speaker configuration you have connected need to be made in "1. AccuEQ Room Calibration" (P20) in Initial Setup. Note that if you are using height speakers, set "Speaker Channels" to "5.1.2 ch" in the setting screen. Select "7.1.2 ch" if you have connected both surround back speakers and height speakers. 2 1 Speaker cable, 2 Subwoofer cable Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and - wires touch each other, the protection circuit will be activated. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
9
> Before start
> Hookup
> Setup
> Playback
> Part Names
Step2: Connect the Speakers
1
2
1/2˝
(12 mm)
1
Speaker cable,
2
Subwoofer cable
in case of:
Pages 3 to 7
Connect
123456
for a 5.1-channel system. With a
7.1-Channel System (with Surround Back Speakers), also
connect
7
and
8
. With a 7.1-Channel System (with
Height Speakers), connect
9:
. Up to two powered
subwoofers can be connected. The same signal is output
from each of the SUBWOOFER jacks.
0
You can also connect both
78
and
9:
. However,
you can only output audio from one set of
78
or
9:
at a time. When you have connected both, you can
select which speakers to prioritize with "Speaker
Layout" (
P26) in the Quick Menu.
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
Setup
0
Settings for the speaker configuration you have
connected need to be made in "1. AccuEQ Room
Calibration" (
P20) in Initial Setup. Note that if you
are using height speakers, set "Speaker Channels"
to "5.1.2 ch" in the setting screen. Select "7.1.2 ch"
if you have connected both surround back
speakers and height speakers.