Onkyo TX-SR304 Owner Manual - Page 51

Advanced Setup

Get Onkyo TX-SR304 PDF manuals and user guides View all Onkyo TX-SR304 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

5943@&OCPPL 1BHF  5VFTEBZ +BOVBSZ Advanced Setup Advanced Speaker Settings The advanced speaker settings cannot be changed while headphones are connected, Speaker set B is on, or the multichannel input is being used. Crossover Frequency This setting only applies to the speakers that you specified as Small in the "Speaker Configuration" on page 34. To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers. 1 RECEIVER Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button. SETUP 2 Use the Up and Down [ ]/[ ] buttons to select "1. SP Config," and then press [ENTER]. ENTER 3 Use the Down [ ] button to select "Crossover," and then use the Left and Right [ ]/[ ] but- tons to select a crossover fre- quency. Use the diameter of the smallest speaker in your system when choosing the crossover frequency. Speaker cone diameter Crossover frequency Over 8 in. (20 cm) 40/50/60Hz 6-1/2 to 8 in. (16-20 cm) 80Hz 5-1/4 to 6-1/2 in. (13-16 cm) 100Hz (default) 3-1/2 to 5-1/4 in. (9-13 cm) 120Hz Under 3-1/2 in. (9 cm) 150/200Hz* *Choose the setting suitable for the speaker. Continue with step 4 of the "Double Bass" setting below. Notes: • For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly. • Choose a higher crossover frequency if you want more sound from your subwoofer. Double Bass With the Double Bass function, you can boost bass output by feeding bass sounds from the front left and right channels to the subwoofer. This function can be set only if the Subwoofer setting (step 3) is set to Yes, and the Front setting (step 4) is set to Large in the Speaker Configuration on page 34. 4 Use the Down [ ] button to select "Double Bass," and then use the Left and Right [ ]/[ ] buttons to select: On: Double Bass function on. Bass from the front left and right channels is also fed to the subwoofer (default). Off: Double Bass function off. 5 SETUP Press the [SETUP] button. Setup closes. When you want to go back up one menu level to "SP Config," press the [RETURN] button. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
51
Advanced Setup
Crossover Frequency
This setting only applies to the speakers that you speci-
fied as
Small
in the “Speaker Configuration” on page 34.
To get the best bass performance from your speaker sys-
tem, you need to set the crossover frequency according
to the size and frequency response of your speakers.
Notes:
•
For a more accurate setting, look up the frequency
response in the manuals supplied with your speakers
and set accordingly.
•
Choose a higher crossover frequency if you want more
sound from your subwoofer.
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting (step 3) is set to Yes, and the
Front setting (step 4) is set to Large in the Speaker Con-
figuration on page 34.
Advanced Speaker Settings
1
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
2
Use the Up and Down [
]/[
]
buttons to select “1. SP Config,”
and then press [ENTER].
3
Use the Down [
] button to
select “Crossover,” and then use
the Left and Right [
]/[
] but-
tons to select a crossover fre-
quency.
Use the diameter of the smallest
speaker in your system when choosing
the crossover frequency.
The advanced speaker settings cannot be
changed while headphones are connected,
Speaker set B is on, or the multichannel input
is being used.
SETUP
RECEIVER
ENTER
*Choose the setting suitable for the speaker.
Continue with step 4 of the “Double
Bass” setting below.
4
Use the Down [
] button to
select “Double Bass,” and then
use the Left and Right [
]/[
]
buttons to select:
On:
Double Bass function on.
Bass from the front left and
right channels is also fed to
the subwoofer (default).
Off:
Double Bass function off.
5
Press the [SETUP] button.
Setup closes.
When you want to go back up one
menu level to “SP Config,” press the
[RETURN] button.
Speaker cone
diameter
Crossover
frequency
Over 8 in.
(20 cm)
40/50/60Hz
6-1/2 to 8 in.
(16–20 cm)
80Hz
5-1/4 to 6-1/2 in.
(13–16 cm)
100Hz (default)
3-1/2 to 5-1/4 in.
(9–13 cm)
120Hz
Under 3-1/2 in.
(9 cm)
150/200Hz*
SETUP
TX-SR304_En.book Page 51 Tuesday, January 24, 2006 10:01 AM