Onkyo TX-SR333 User Manual - Page 29

⿠⿠Try resetting your iPod/iPhone. ⿠⿠Depending on your iPod/iPhone model and generation, some buttons may not work as expected. ■■The unit unexpectedly selects my iPod/iPhone as the input source ⿠⿠Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks. ■■iPod/iPhone does not work properly ⿠⿠Try reconnecting your iPod/iPhone. Zone Function ■■There is no sound ⿠⿠Audio signal from input selector can be output for Zone function. Connect audio components using the analog audio (RCA) cable as audio signal from the components connected using HDMI or digital audio cable cannot be output for one function. Note that connected components may have to be setup to output analog audio signal. Blu-ray Disc player AUDIO OUT Bluetooth ■■Music playback is unavailable on the unit even after successful Bluetooth connection ⿠⿠Depending on the characteristics or specifications of your Bluetooth-enabled device, playback on the unit is not guaranteed. ⿠⿠When the audio volume of your Bluetooth-enabled device is set low, the playback of audio may be unavailable. Volume up the Bluetooth-enabled device. ⿠⿠Depending on the Bluetooth-enabled device, Send/ Receive selector switch may be provided. Select Send mode. ⿠⿠Even when a music file is playing on the Bluetoothenabled device, the sound can not be played if the connection is not established with the unit. Make sure that the unit is connected (this unit is selected as the sound output destination). ■■Sound is interrupted ⿠⿠Problem may be occurring at the Bluetooth-enabled device. Check the information on a webpage. ■■The audio quality is poor after connection with a Bluetooth-enabled device ⿠⿠The Bluetooth reception is poor. Move the Bluetooth- enabled device closer to the unit or remove any obstacle between the Bluetooth-enabled device and this unit. ■■Can not connect with this unit ⿠⿠Try plugging/unplugging the power of the unit and try turning on/off the Bluetooth-enabled device. Re-startup of the Bluetooth-enabled device may be effective. ⿠⿠The Bluetooth-enabled device does not support the profiles required for this unit. ⿠⿠The Bluetooth function of the Bluetooth-enabled device is not enabled. Refer to the user manual of the Bluetooth-enabled device for how to enable the function. ⿠⿠Near devices such as microwave oven or cordless phone, which use the radio wave in the 2.4 GHz range, a radio wave interference may occur, which disables the use of the AV receiver. ■■Bluetooth connection can not be built ⿠⿠When building a Bluetooth connection between this unit and your Bluetooth-enabled device for the first time, if the connection fails, clear "Pairing Info" in "12. Bluetooth", turn off and then on again your Bluetoothenabled device to clear the device name, and build the connection again. ⿠⿠If there is a metallic object near the unit, Bluetooth connection may not be possible as the metal can effect on the radio wave. Troubleshooting ■■The Bluetooth Auto Reconnect function does not work. ⿠⿠This function may not work depending on your Bluetooth-enabled device. In this case, play on your Bluetooth-enabled device after pairing with this unit. USB Function ■■USB storage device is not displayed ⿠⿠Make sure that USB storage device and USB cable are securely plugged to the USB port of this AV receiver. ⿠⿠Remove the USB storage device from the AV receiver once, and then try re-connecting. ⿠⿠Operability of a USB bus powered hard disk that receives power from the unit via the USB port is not guaranteed. ⿠⿠Depending on the type of format, the playback may not be performed normally. Check the type of the file formats that is supported. ⿠⿠USB storage device with security functions may not be played. Others ■■Power consumption in standby mode ⿠⿠In the following cases, the power consumption in standby mode may reach up to a maximum of 55 W: - When "HDMI CEC (RIHD)" is set to "On". (Depending on the TV status, the AV receiver will enter normal standby mode.) - When "HDMI Through" is set to other than "Off". ■■The sound changes when I connect my headphones ⿠⿠When a listening mode other than Direct or Mono is selected, connecting a headphone automatically selects Stereo. ■■How do I change the language of a multiplex source ⿠⿠Select "Main" or "Sub" for "Input Ch(Mux)" in "8. Audio Adjust". ■■The RI functions do not work ⿠⿠To use RI, you must make an RI connection and an analog audio (RCA) cable between the component and AV receiver, even if they are connected digitally. ⿠⿠While Zone 2 is selected, the RI functions do not work. 29