Onkyo TX-SR504 Owner Manual - Page 65

Video Attenuation, Video ATT:0, Video ATT:2, Outputting S-Video Sources from the Composite, Video

Get Onkyo TX-SR504 - 7.1 Channel A/V Receiver PDF manuals and user guides
UPC - 751398006937
View all Onkyo TX-SR504 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Troubleshooting-Continued The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit's malfunction. Before you record important data, make sure that the material will be recorded correctly. Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby. Memory Backup The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it's unplugged or in the case of a power failure. Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates. The following settings can be made for the S-Video and composite video inputs You must use the buttons on the unit to make these settings. 1. While holding down the input selector button for the input source that you want to set, press the [SETUP] button. 2. Use the Up and Down [ ]/[ ] buttons to select a setting (see below). 3. Use the Left and Right [ ]/[ ] buttons to change the setting: 4. Press the [SETUP] button when you've finished. • Video Attenuation This setting can be made for the DVD, VIDEO 1, VIDEO 2, or VIDEO 3 input. If you have a games console connected to an S-Video or composite video input, and the picture isn't very clear, you can attenuate the gain. Video ATT:0: (default). Video ATT:2: Gain is reduced by 2 dB. • Outputting S-Video Sources from the Composite Video Outputs This setting can be made for the DVD, VIDEO 1, or VIDEO 2 input. With this setting, you can output S-Video input sources from the composite video outputs, useful if your TV doesn't have any S-Video inputs. Y/C Mix:Off: S-Video input signals are output by only S-Video outputs (default). Y/C Mix:On: S-Video input signals are output by S-Video outputs and composite video outputs. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
65
Troubleshooting
—Continued
The following settings can be made for the
S-Video and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1.
While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2.
Use the Up and Down [
]/[
] buttons to select a
setting (see below).
3.
Use the Left and Right [
]/[
] buttons to change
the setting:
4.
Press the [SETUP] button when you’ve finished.
•
Video Attenuation
This setting can be made for the DVD, VIDEO 1,
VIDEO 2, or VIDEO 3 input.
If you have a games console connected to an S-Video
or composite video input, and the picture isn’t very
clear, you can attenuate the gain.
Video ATT:0:
(default).
Video ATT:2:
Gain is reduced by 2 dB.
•
Outputting S-Video Sources from the Composite
Video Outputs
This setting can be made for the DVD, VIDEO 1, or
VIDEO 2 input.
With this setting, you can output S-Video input
sources from the composite video outputs, useful if
your TV doesn’t have any S-Video inputs.
Y/C Mix:Off:
S-Video input signals are output by
only S-Video outputs (default).
Y/C Mix:On:
S-Video input signals are output by
S-Video outputs and composite video outputs.
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
Memory Backup
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other set-
tings when it’s unplugged or in the case of a power fail-
ure. Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system. Once it has been charged, the AV
receiver will retain the settings for several weeks,
although this depends on the environment and will be
shorter in humid climates.