Onkyo TXSR502B Owner Manual - Page 30

5943@&OCPPL 1BHF  5VFTEBZ 'FCSVBSZ 1. Connecting the TX-SR502/TX-SR502E-Continued Connecting Onkyo Components To use , you must make an analog audio connection (RCA) between the TX-SR502/ TX-SR502E and the other component, even if they are connected digitally. With (Remote Interactive) you can control your -compatible Onkyo CD player, DVD player, and so on with the TX-SR502/TX-SR502E's remote controller, and use the following special functions: Auto Power On/Standby When you start playback on a component connected via , if the TX-SR502/TX-SR502E is in Standby, it will turn on and select that component as the input source automatically. Similarly, when the TX-SR502/ TX-SR502E is set to Standby, all components connected via also enter Standby. This function will not work if the component's power cord is connected to the TX-SR502/TX-SR502E's AC OUTLET. Direct Change When playback is started on a component connected via , the TX-SR502/TX-SR502E automatically selects that component as the input source. If your DVD player is connected to the TX-SR502/TX-SR502E's multichannel input, you must press the [MULTI CH] button to enjoy all channels (see page 34). This is because the Direct Change function only selects the FRONT DVD IN sockets. Remote Control You can use the TX-SR502/TX-SR502E's remote controller to control other -compatible Onkyo components. IN L REMOTE CONTROL COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3IN DVD IN OUT AM FM 75 Y PB DIGITAL IN OPTICAL 3 2 PR COAXIAL 1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD MONITOR IN OUT VIDEO S VIDEO IN OUT IN L SUBWOOFER PRE OUT R CD TAPE IN IN OUT IN FRONT SURR CENTER L L R VIDEO 2 VIDEO 1 R DVD SUB WOOFER R CD FRONT L R DVD e.g., CD player e.g., DVD player R L ANALOG AUDIO OUT R L ANALOG AUDIO OUT Notes: • Push plugs in all the way to make good connections. • Use only cables for connections. cables are supplied with Onkyo players (DVD, CD, etc.). • Some components have two sockets, you can connect either one to the TX-SR502/TX-SR502E. The other is for connecting additional -compatible components. 30 • Connect the TX-SR502/TX-SR502E's socket to only Onkyo components. Connecting to other manufacturer's components may cause them to malfunction. • Some components may not support all functions. Refer to the manuals supplied with your components. Connecting the Power Cords of Other Components The TX-SR502/TX-SR502E has AC outlet on its rear panel for connecting the power cord of another AV component. The other component's power switch can be left in the ON position so that it turns on or off when the TX-SR502/TX-SR502E is set to On or Standby. FRONT SPEAKERS B L Class 2 Wiring FRONT SPEAKERS A L SURROUND SPEAKERS L CENTER SPEAKER AC OUTLET AC 120V 60 Hz SWITCHED 120W 1 A MAX. R R R AV RECEIVER MODEL NO. TX-SR502 SURROUND BACK SPEAKER AC OUTLET SWITCHED 100W MAX. AC OUTLET AC 120V 60 Hz SWITCHED 120W 1 A MAX. European and some Asian models American model Caution: • Make sure that the capacity of the component that you connect to the AC OUTLET does not exceed the stated capacity (e.g., 100 W). Note: • Onkyo components with sockets should be con- nected to regular wall outlets. • The connector type and capacity will depend on the country in which you purchased the TX-SR502/ TX-SR502E. Connecting the Power Cord Notes: • Before connecting the power cord, connect all of your speakers and AV components. • Turning on the TX-SR502/TX-SR502E may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the TX-SR502/TX-SR502E into a different branch circuit.