Optoma UHD51ALV UHD51ALV User Manual - Page 62

Other problems, Remote control problems, Set the 3D --> 3D Format to SBS.

Get Optoma UHD51ALV PDF manuals and user guides View all Optoma UHD51ALV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

ADDITIONAL INFORMATION T wo images, side-by-side format ‡‡ Set the "3D" --> "3D Format" to "SBS". Other problems T he projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. L amp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 53-54. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within ±15° (horizontally) or ±10° (vertically) to the IR receiver on the projector. ‡‡ Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (~22 ft) of the projector. ‡‡ Make sure battery is inserted correctly. ‡‡ Replace battery if it is exhausted. 62 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
English
62
ADDITIONAL INFORMATION
Two images, side-by-side format
±
Set the “3D” --> ”3D Format” to “SBS“.
Other problems
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
±
When the lamp reaches its end of life, it will burn out and may make a loud popping sound.
If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages
53-54
.
Remote control problems
If the remote control does not work
±
Check the operating angle of the remote control is pointed within ²15° (horizontally) or ²10° (vertically)
to the IR receiver on the projector.
±
Make sure there are not any obstructions between the remote control and the projector. Move to within
7 m (~22 ft) of the projector.
±
Make sure battery is inserted correctly.
±
Replace battery if it is exhausted.