Optoma W460 W460 User Manual - Page 5

Precautions, Warning, Do not°

Get Optoma W460 PDF manuals and user guides View all Optoma W460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Precautions Please follow all warnings, precautions and maintenance as recommended in this user's guide. Warning ‡‡ Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes. As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015. ‡‡ To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. ‡‡ Please do not open or disassemble the projector as this may cause electric shock. ‡‡ When replacing the lamp, please allow the unit to cool down. Follow instructions as described on page 64. ‡‡ This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. ‡‡ Reset the "Lamp Reset" function from the on-screen display "System / Lamp Setting" menu after replacing the lamp module (refer to page 36). Note: When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under "Replacing the lamp" on page 64. ‡‡ When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down. ‡‡ Do not use lens cap when projector is in operation. ‡‡ When the lamp is approaching to the end of its life time, the message "Replacement suggested" will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible. Do: ‡‡ Turn off and unplug the power plug from the AC outlet before cleaning the product. ‡‡ Use a soft dry cloth with mild detergent to clean the display housing. ‡‡ Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Do not: ‡‡ Block the slots and openings on the unit provided for ventilation. ‡‡ Use abrasive cleaners, waxes or solvents to clean the unit. ‡‡ Use under the following conditions: ±± In extremely hot, cold or humid environments. ‡‡ Ensure that the ambient room temperature is within 5 - 40°C ‡‡ Relative Humidity is 10 - 85% (Max.), non-condensing ±± In areas susceptible to excessive dust and dirt. ±± Near any appliance generating a strong magnetic field. ±± In direct sunlight. English 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English
5
Precautions
Please follow all warnings, precautions and maintenance as recommended in this user’s guide.
Warning
±
Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes.
As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.
±
To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture.
±
Please do not open or disassemble the projector as this may cause electric shock.
±
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on page
64.
±
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
±
Reset the “Lamp Reset” function from the on-screen display “System / Lamp Setting” menu after
replacing the lamp module (refer to page 36).
Note°
When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been
replaced. To replace the lamp, follow the procedures listed under “Replacing the lamp” on page 64.
±
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
±
Do not use lens cap when projector is in operation.
±
When the lamp is approaching to the end of its life time, the message “Replacement suggested” will
show on the screen.
Please contact your local reseller or service center to change the lamp as soon as possible.
Do°
±
Turn off and unplug the power plug from the AC outlet before cleaning the product.
±
Use a soft dry cloth with mild detergent to clean the display housing.
±
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Do not°
±
Block the slots and openings on the unit provided for ventilation.
±
Use abrasive cleaners, waxes or solvents to clean the unit.
±
Use under the following conditions:
±
In extremely hot, cold or humid environments.
±
Ensure that the ambient room temperature is within 5 - 40°C
±
Relative Humidity is 10 - 85% (Max.), non-condensing
±
In areas susceptible to excessive dust and dirt.
±
Near any appliance generating a strong magnetic field.
±
In direct sunlight.