Optoma X312 Manual - Page 3

Precautions - lamp

Get Optoma X312 PDF manuals and user guides View all Optoma X312 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user's guide. ▀■ Warning- Do not look into the projector's lens when the lamp is on. The bright light may hurt and damage your eyes. ▀■ Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. ▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock. ▀■ Warning- When replacing the lamp, please allow the unit to cool down. Follow instructions as described on pages 52-53. ▀■ Warning- This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. ▀■ Warning- Reset the "Lamp Reset" function from the on-screen display "OPTIONS | Lamp Settings" menu after replacing the lamp module (refer to page 44). ▀■ Warning- When switching the projector off, please ensure the cooling cycle has been completed before  When the lamp disconnecting power. Allow 90 seconds for the reaches the end of its life, the pro- projector to cool down. jector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the ▀■ Warning- When the lamp is approaching the end of its lifetime, the message "Lamp Warning: Lamp life exceeded." will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible. procedures listed under "Replacing the Lamp" section on pages 52-53. ▀■ Warning- Not all projectors come with a lens cap. For your safety, if the projector is equipped with a lens cap please ensure to remove it before you turn on the projector. 3 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
3
English
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀
■
Warning-
Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀
■
Warning-
To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀
■
Warning-
Please do not open or disassemble the projector as
this may cause electric shock.
▀
■
Warning-
When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
52-53.
▀
■
Warning-
This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀
■
Warning-
Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 44).
▀
■
Warning-
When switching the projector off, please ensure
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀
■
Warning-
When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
▀
■
Warning-
Not all projectors come with a lens cap.
For your
safety, if the projector is equipped with a lens cap
please ensure to remove it before you turn on the
projector.
When the lamp
reaches the end
of its life, the pro-
jector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 52-53.