Panasonic CT2511HDB CT2511HDB User Guide - Page 14

Testing The Settings In The Clone Box, Testing The Clone Box Battery

Page 14 highlights

• The red LED will flash while the data is uploaded into the box. The green LED will light for about two (2) seconds when the procedure is complete. • If the green LED does not light for about two (2) seconds, retry by holding the ALT button while pressing the LEARN button. 7. Disconnect the clone box from the • El indicador rojo emitirá una luz intermitente mientras la información es grabada en la caja de clonación. El indicador verde emitirá una luz continua por aproximadamente dos segundos cuando el procedimiento halla concluido. • Si el indicador verde no emite luz por los aproximados dos segundos, vuelva a intentar presionando el botón ALT y LEARN simultaneamente. television and turn it OFF. 7. Desconecte la caja de clonación del la 8. Reset the volume on the television. televisión y APAGUELA. 9. Refer to the section entitled Setting Up 8. Reajuste el volumen en la televisión. Other Televisions Using the Clone Box 9. Refiérase a la sección titulada (TEACH). Configurando otras televisiones usando su caja de clonación (ENSEÑA). Testing the Settings in the Clone Box This test compares the clone box settings with the television settings. The television must be in Commercial (Hotel) mode. 1. Press the POWER ON button on the clone box. Probando la configuración en la caja de clonación. Mediante este procedimiento se compara la configuración de la caja de clonación con la de la televisión. La televisión debe estar en la modalidad comercial (hotel). • The LEDs will flash red and green to confirm power is ON. 1. Presione el botón POWER ON en la caja de clonación. 2. Connect the clone box to the Digital Interface port on the back of the television. • Los indicadores rojo y verde emitirán una luz intermitente para confirmar que la caja de clonación está encendida. • The television must be plugged into an AC outlet but can be either OFF or ON. 2. Conecte la caja de clonación a la interface digital en la parte posterior de la televisión. 3. Press the TEST button. • The LEDs will flash red and green while the data is compared. The green LED will light for about two (2) seconds if the settings in the box match the television. 4. Disconnect the clone box from the television and turn it OFF. Testing the Clone Box Battery 1. Press the POWER ON button on the clone box. • Aunque la televisión puede estar encendida o apagada debe estar conectada al suministro de corriente alterna. 3. Presione el botón TEST (Prueba). • Los indicadores rojo y verde emitirán una luz intermitente mientras se compara la información. El indicador emitirá una luz verde continua por aproximadamente dos segundos si la configuración de la caja es igual a la de la televisión. 4. Desconecte la caja de clonación de la televisión y APAGUELA. • The LEDs will flash red and green to confirm Probando la pila de la caja de clonación power is ON. 1. Presione el botón POWER ON en la caja 2. Hold the ALT button while pressing the de clonación. TEST button. • The LEDs will alternately flash red and green while the box is tested. • Los indicadores rojo y verde emitirán una luz intermitente para confirmar que la caja de clonación está encendida. 2. Mientras mantiene presionado el botón Note: Replace the 9 volt battery if the LEDs do not flash red and green. • The green LED will light for about two (2) ALT oprima el botón TEST (Prueba). • Los indicadores rojo y verde emitirán una luz alternada durante la revisión de la caja. seconds, if battery is charged. Note: If the green LED does not light for about two (2) seconds at the end of the test, new data must be downloaded into the box. - 14 - Nota: Si el indicador no emite la luz verde y roja en forma intermitente, reemplace la pila de 9 voltios. • Si la pila está cargada, el indicador emitirá un luz verde intermitente por aproximadamente dos segundos.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

– 14 –
El indicador rojo emitirá una luz intermitente
mientras la información es grabada en la caja
de clonación. El indicador verde emitirá una
luz
continua
por
aproximadamente
dos
segundos cuando el procedimiento halla
concluido.
Si el indicador verde no emite luz por los
aproximados dos segundos, vuelva a intentar
presionando
el
botón
ALT
y
LEARN
simultaneamente.
7. Desconecte la caja de clonación del la
televisión y APAGUELA.
8.
Reajuste el volumen en la televisión.
9. Refiérase
a
la
sección
titulada
Configurando otras televisiones usando su
caja de clonación (ENSEÑA).
Probando la configuración en la caja
de clonación.
Mediante este procedimiento se compara la
configuración de la caja de clonación con la de la
televisión.
La
televisión
debe
estar
en
la
modalidad comercial (hotel).
1.
Presione el botón
POWER ON
en la caja
de clonación.
Los indicadores rojo y verde emitirán una luz
intermitente para confirmar que la caja de
clonación está encendida.
2.
Conecte la caja de clonación a la interface
digital en la parte posterior de la televisión.
Aunque la televisión puede estar encendida o
apagada debe estar conectada al suministro
de corriente alterna.
3.
Presione el botón
TEST
(Prueba).
Los indicadores rojo y verde emitirán una luz
intermitente
mientras
se
compara
la
información. El indicador emitirá una luz verde
continua por aproximadamente dos segundos
si la configuración de la caja es igual a la de la
televisión.
4. Desconecte la caja de clonación de la
televisión y APAGUELA.
Probando la pila de la caja de clonación
1.
Presione el botón
POWER ON
en la caja
de clonación.
Los indicadores rojo y verde emitirán una luz
intermitente para confirmar que la caja de
clonación está encendida.
2. Mientras mantiene presionado el botón
ALT
oprima el botón
TEST
(Prueba).
Los indicadores rojo y verde emitirán una luz
alternada durante la revisión de la caja.
Nota:
Si el indicador no emite la luz verde y roja en
forma intermitente, reemplace la pila de 9
voltios.
Si la pila está cargada, el indicador emitirá un
luz verde intermitente por aproximadamente
dos segundos.
The red LED will flash while the data is
uploaded into the box. The green LED will
light for about two (2) seconds when the
procedure is complete.
If the green LED does not light for about two
(2) seconds, retry by holding the
ALT
button
while pressing the
LEARN
button.
7. Disconnect
the
clone
box
from
the
television and turn it OFF.
8.
Reset the volume on the television.
9. Refer to the section entitled
Setting Up
Other Televisions
Using the Clone Box
(TEACH).
Testing the Settings in the Clone Box
This test compares the clone box settings with
the television settings. The television must be in
Commercial (Hotel) mode.
1.
Press the
POWER ON
button on the clone
box.
The LEDs will flash red and green to confirm
power is ON.
2. Connect the clone box to the Digital
Interface port on the back of the television.
The television must be plugged into an AC
outlet but can be either OFF or ON.
3.
Press the
TEST
button.
The LEDs will flash red and green while the
data is compared. The green LED will light for
about two (2) seconds if the settings in the box
match the television.
4. Disconnect
the
clone
box
from
the
television and turn it OFF.
Testing the Clone Box Battery
1.
Press the
POWER ON
button on the clone
box.
The LEDs will flash red and green to confirm
power is ON.
2. Hold the
ALT
button while pressing the
TEST
button.
The LEDs will alternately flash red and green
while the box is tested.
Note:
Replace the 9 volt battery if the LEDs do
not flash red and green.
The green LED will light for about two (2)
seconds, if battery is charged.
Note:
If the green LED does not light for about
two (2) seconds at the end of the test, new
data must be downloaded into the box.