Panasonic DMRE85H DMRE85H User Guide - Page 48

Error messages Reference On the television Cannot finish recording completely. Cannot play. Cannot record on the disc. Please check the disc. Unable to format. Cannot record. Disc is full. Cannot record. Maximum number of titles exceeded. Error has occurred. Please press ENTER. No disc Please change the disc. This is a non-recordable disc. This disc is not formatted properly. $ ≥The program was copy-protected. ≥The HDD or disc may be full. ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.). ≥The disc may be dirty or scratched. ≥Create space by erasing any unnecessary titles. [HDD] [RAM] ≥Use a new disc. [RAM] [DVD-R] ≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering ("SELF CHECK" appears on the unit's display). ≥The disc may be upside down. ≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to remove it and check it for scratches or dirt. (The unit turns off automatically after you open the tray.) ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R. ≥You inserted an unformatted DVD-RAM. Format the disc with this unit. ≥The operation is prohibited by the unit or disc. Page - - - 15 26, 31, 39 - - - 15 - 39 - On the unit's display CHK REMOTE ("∑" stands for a number.) ≥The remote control and main unit are using different codes. Change the code on the 13 remote control. Press and hold [ENTER] and the indicated number button at the same time for more than 2 seconds. HARD ERR HDD SLP NO READ PLEASE WAIT SELF CHECK UNSUPPORT U14 U99 ≥If there is no change after turning the unit on and off, consult the dealer where the unit was - purchased. ≥In order to extend HDD life, the HDD is in SLEEP mode. Press [HDD] to activate. 15 ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit. 15 ≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [< OPEN/CLOSE] - on the main unit to eject the disc. ≥Displayed when the unit is started. This is not a malfunction. - ≥There was a power failure or the AC plug was disconnected while the unit was on. The unit - is carrying out its recovery process. Wait until the message disappears. ≥You have inserted a disc the unit cannot play or record on. 14 ≥The unit is hot. - The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears. Select a position with good ventilation when installing the unit. Do not block the cooling fan on the rear of the unit. ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to - standby. Now press [POWER Í/I] on the main unit again to turn the unit on. Product Service 1. Damage requiring service-The unit should be serviced by qualified service personnel if: (a) The AC power supply cord or AC adaptor has been damaged; or (b) Objects or liquids have gotten into the unit; or (c) The unit has been exposed to rain; or (d) The unit does not operate normally or exhibits a marked change in performance; or (e) The unit has been dropped or the cabinet damaged. 2. Servicing-Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel. 3. Replacement parts-When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards. 4. Safety check-After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition. Product information For product information or assistance with product operation: In the U.S.A., refer to "Customer Services Directory" on page 52. RQT7305 In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, or visit the website (www.panasonic.ca), or an 48 authorized Servicentre closest to you.