Panasonic ER-GN70 Operating Instructions - Page 9

Using

Get Panasonic ER-GN70 PDF manuals and user guides View all Panasonic ER-GN70 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

English Using 1. R emove the protective cap and hold the main body so as not to block the exhaust hole ( ). 2. Slide the power switch on the main body to the "O" position to turn on the power. • The outer blade surface may get a little warm during use, but performance will not be affected. 3. Trim Trimming your nose hair and ear hair 1. Insert the tip ( ) of the outer blade into your nostril or ear canal. • Insert it slowly so as not to injure your nostril or ear canal. 2. C ut the nose hair and ear hair by moving the main body. • Cut hairs using the tip ( ) of the outer blade (metallic part). • Some trimmings may remain inside your nostril or ear canal after cutting, so remove them using a tissue or similar. Outlining your eyebrows, moustache, or beard 1. Apply the tip of the outer blade to the hair (eyebrow, moustache or beard) you would like to cut. 2. C ut the hair by moving the appliance slowly against the direction of hair growth. • You cannot trim the hair to length with this appliance. • It is not suitable for the hair below 0.5 mm (1/64˝). 4. After use, slide the power switch on the main body to the "I" position to turn off the power and clean it. (See page 10). 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
9
English
Using
1. Remove the protective cap and hold
the main body so as not to block the
exhaust hole (
).
2. Slide the power switch on the main body
to the “O” position to turn on the power.
•
The outer blade surface may get a little
warm during use, but performance will
not be affected.
3. Trim
Trimming your nose hair and ear hair
1. Insert the tip (
) of the outer blade into your nostril or ear
canal.
•
Insert it slowly so as not to injure your nostril or ear canal.
2. Cut the nose hair and ear hair by moving the main body.
•
Cut hairs using the tip (
) of the outer blade (metallic part).
•
Some trimmings may remain inside your nostril or ear canal
after cutting, so remove them using a tissue or similar.
Outlining your eyebrows, moustache, or beard
1. Apply the tip of the outer blade to the hair (eyebrow,
moustache or beard) you would like to cut.
2. Cut the hair by moving the appliance slowly against the
direction of hair growth.
•
You cannot trim the hair to length with this appliance.
• It is not suitable for the hair below 0.5 mm (1/64˝).
4. After use, slide the power switch on the main body to the
“I” position to turn off the power and clean it.
(See page 10).