Panasonic ES-RT97-S Operating Instructions - Page 19

Troubleshooting, When the water does not drain from the cleaning tray, Self-cleaning recharger

Get Panasonic ES-RT97-S PDF manuals and user guides View all Panasonic ES-RT97-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

►►When the water does not drain from the cleaning tray ••Do not tilt the self-cleaning recharger to pour out water. Doing so may cause the cleaning liquid in the cleaning liquid unit to spill or cause the self-cleaning recharger to malfunction. Beard trimmings may clog the drain at the bottom of the cleaning tray. In this case, you cannot clean or dry the shaver. Push the beard trimmings down through the drain with a toothpick etc. Problem The mode does not start. Troubleshooting ►►Self-cleaning recharger Problem Action If the shaver is not cleaned for more than 2 weeks, first clean to remove beard trimmings. The blade has not been thoroughly washed. Do not add detergent and water except when replacing the cleaning liquid. Doing so may deteriorate the cleaning function. (See page 15.) After cleaning, oil-like droplets may remain on the outside of the foil frame. This is the lubricating component of the cleaning liquid and does not indicate a problem. You may wipe it off with a soft cloth. The STATUS lamp glows. See page 20. Cleaning liquid has accumulated in the cleaning tray. The cleaning liquid unit cannot be removed. Action Check that the AC adaptor is connected to the self-cleaning recharger, and that the AC adaptor is plugged in to a household outlet. (See page 11.) Confirm that the shaver is properly attached to the selfcleaning recharger. (See page 11.) The Clean or Dry function may stop out of recommended ambient temperature range. (5 - 35 °C (41 - 95 °F)) Check if the STATUS lamp glows. (See page 20.) Remove any waste, etc. that has accumulated in the drain at the bottom of the cleaning tray. (See this page.) If you use the self-cleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may accumulate in the cleaning tray. Place the self-cleaning recharger on a hard, flat surface. When the self-cleaning recharger is lifted, or on the soft surface such as carpets, the lock release lever will not fit in the recharger properly. In that case, the cleaning liquid unit cannot be removed. 19  English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
19
English
►
When the water does not drain from the cleaning tray
•
Do not tilt the self‑cleaning recharger to pour out water. Doing so
may cause the cleaning liquid in the cleaning liquid unit to spill or
cause the self‑cleaning recharger to malfunction.
Beard trimmings may clog the drain at the
bottom of the cleaning tray.
In this case, you cannot clean or dry the shaver.
Push the beard trimmings down through the
drain with a toothpick etc.
Troubleshooting
►
Self-cleaning recharger
Problem
Action
The blade has not been
thoroughly washed.
If the shaver is not cleaned for
more than 2 weeks, first clean to
remove beard trimmings.
Do not add detergent and water
except when replacing the
cleaning liquid.
Doing so may deteriorate the
cleaning function. (See page 15.)
After cleaning, oil‑like droplets may
remain on the outside of the foil
frame. This is the lubricating
component of the cleaning liquid
and does not indicate a problem.
You may wipe it off with a soft cloth.
The STATUS lamp glows.
See page 20.
Problem
Action
The mode does not start.
Check that the AC adaptor is
connected to the self‑cleaning
recharger, and that the AC
adaptor is plugged in to a
household outlet. (See page 11.)
Confirm that the shaver is
properly attached to the self‑
cleaning recharger.
(See page 11.)
The Clean or Dry function may
stop out of recommended
ambient temperature range.
(5 – 35 °C (41 – 95 °F))
Check if the STATUS lamp glows.
(See page 20.)
Cleaning liquid has
accumulated in the
cleaning tray.
Remove any waste, etc. that has
accumulated in the drain at the
bottom of the cleaning tray.
(See this page.)
If you use the self‑cleaning
recharger when the shaver is wet
or when soap or shaving gel is on
the shaver, cleaning liquid may
accumulate in the cleaning tray.
The cleaning liquid unit
cannot be removed.
Place the self‑cleaning recharger
on a hard, flat surface.
When the self‑cleaning recharger
is lifted, or on the soft surface
such as carpets, the lock release
lever will not fit in the recharger
properly. In that case, the cleaning
liquid unit cannot be removed.