Panasonic MC-UL427 MC-UL427 Owner's Manual (Multi Language) - Page 46

MC-V390B, Type UB12 around, Lay vacuum cleaner on the floor - belt

Get Panasonic MC-UL427 PDF manuals and user guides View all Panasonic MC-UL427 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Belt Courroie Correa Motor Shaft Arbre du moteur Eje del motor Carpet/Bare Floor Selector Shaft Arbre d'entraînement du sélecteur tapis/plancher Selector alfombra-piso ➢ Loop new belt (part number MC-V390B, Type UB12) around Carpet/Bare Floor selector shaft and agitator belt groove. Make sure belt is routed in the belt guide as shown. See illustration for correct belt routing. ➢ Reinstall agitator back into nozzle by placing end caps into grooves. Motor Shaft Arbre d'entrainement du moteur Eje del motor Belt Courroie Correa Agitator Agitateur Agitador End Cap Bouchon Tapa del extremo Groove Rainure Ranura Tabs Languettes Lengüetas 2 1 Slots Fentes Ranuras Four Screws Quatre vis Cuatro Tornillos ➢ After reinstalling the agitator, turn it by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely. ➢ Place the vacuum cleaner in the upright position standing on the handle. This will minimize wheel interference when installing lower plate. ➢ Reinstall lower plate by (1) aligning tabs on front edge of lower plate with slots in the nozzle and (2) rotating to installed position. ➢ Lay vacuum cleaner on the floor with the bottom up and nozzle flat. ➢ Install the four screws to the nozzle cover. ➢ Route nozzle hose to hose holder. Align nozzle hose bracket with retaining bracket on body and slide down unit it clicks into place. ➢ Return the vacuum cleaner to the upright position before plugging into an electrical outlet. - 46 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
- 46 -
➢
Reinstall agitator back into nozzle
by placing end caps into grooves.
➢
After reinstalling the agitator, turn it
by hand to make sure that belt is
not twisted or pinched and that all
rotating parts turn freely.
Belt
Correa
Courroie
Motor Shaft
Arbre d’entrainement
du moteur
Eje del motor
End Cap
Tapa del
extremo
Bouchon
Agitator
Agitateur
Agitador
Groove
Rainure
Ranura
Carpet/Bare
Floor Selector
Shaft
tapis/plancher
Selector alfombra-piso
Arbre d'entraînement
du sélecteur
Motor Shaft
Arbre du moteur
Eje del motor
Belt
Courroie
Correa
➢
Loop new belt (part number
MC-V390B, Type UB12) around
Carpet/Bare Floor selector shaft and
agitator belt groove.
Make sure belt
is routed in the belt guide as
shown.
See illustration for correct
belt routing.
2
1
Slots
Fentes
Ranuras
Tabs
Languettes
Lengüetas
➢
Place the vacuum cleaner in the
upright position standing on the
handle. This will minimize wheel
interference when installing lower
plate.
➢
Reinstall lower plate by (1) aligning
tabs on front edge of lower plate
with slots in the nozzle and (2)
rotating to installed position.
Four Screws
Quatre vis
Cuatro Tornillos
➢
Lay vacuum cleaner on the floor
with the bottom up and nozzle flat.
➢
Install the four screws to the nozzle
cover.
➢
Route nozzle hose to hose holder.
Align nozzle hose bracket with
retaining bracket on body and slide
down unit it clicks into place.
➢
Return the vacuum cleaner to the
upright position before plugging
into an electrical outlet.