Panasonic P1SDU PTP1SDU User Guide - Page 30

Lamp unit replacement procedure, Care and maintenance, LAMP TIME RESET, CANCEL, POWER OFF, POWER] OK

Get Panasonic P1SDU - SVGA LCD Projector PDF manuals and user guides
UPC - 791871111253
View all Panasonic P1SDU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

On-screen display LAMP indicator More than 2 250 hours More than 2 500 hours Displayed for 30 seconds. Pressing any button will clear the display. Remains displayed until any button is pressed. Illuminates red during image projection and standby mode. Lamp unit replacement procedure NOTE: B If the lamp usage time has passed 2 500 hours, the projector will switch to standby mode after approximately 10 minutes of operation. The steps ) to / on the next page should thus be completed within 10 minutes. # Disconnect the power cord from the projector by following the procedure on page 28, and check that the area around the lamp unit has cooled down. $ Use a Phillips screwdriver to turn the lamp unit cover fixing screw at the bottom of the projector, and then remove the lamp unit cover. % Use a Phillips screwdriver to loosen the lamp unit fixing screw until the screw turns freely. Then hold the handle of the lamp unit and gently pull the lamp unit out from the projector. Handle A B Lamp unit cover Lamp unit cover fixing screw 58-ENGLISH Lamp unit fixing screw & Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screw. When inserting the new lamp unit, be sure to push it in at the point A and B. ' Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screw. NOTE: B Be sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on. ( Connect the power cord. ) Press the POWER button so that a picture is projected onto the screen. NOTE: B If the power cord was disconnected during projection when the projector was used the last time, projection will start after the power cord is connected. * Press the MENU button to display the "MAIN MENU", and then press the F or G button to select "OTHER SETUP". MENU PICTURE ADJUSTMENT POSITION ADJUSTMENT OTHER SETUP LANGUAGE SETUP SECURITY SETUP SD PICTURE SETUP SELECT ENTER EXIT + Press the ENTER button to display the "OTHER SETUP" menu, and then press the F or G button to select "LAMP RUNTIME". OTHER SETUP AUTO SIGNAL ON TV-SYSTEM AUTO FRONT/REAR FRONT DESK/CEILING DESK HIGHLAND OFF LAMP RUNTIME 2300H SXGA MODE SXGA CTRL PANEL VALID NR OFF SELECT RETRN , Press and hold the ENTER button for approximately 3 seconds. The "LAMP TIME RESET" screen will be displayed. LAMP TIME RESET OK CANCEL - Select "OK" by pressing the I or H button on the remote control unit and then press the ENTER button. The "POWER OFF" confirmation screen will be displayed. POWER OFF [POWER] OK NOTE: B The "POWER OFF" screen will disappear in five seconds. B If the MENU button is pressed, the "LAMP TIME RESET" screen and the "POWER OFF" confirmation screen will be cancelled. . Press the POWER button to turn off the power. / Disconnect the power cord after the POWER button on the projector illuminates red. This will reset the cumulative usage time for the lamp unit to "0". ENGLISH-59 Care and maintenance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
A
B
E
NGLISH
-59
58-E
NGLISH
'
Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screw.
(
Connect the power cord.
)
Press the POWER button so
that a picture is projected onto
the screen.
*
Press the MENU button to
display the “MAIN MENU”, and
then press the
F
or
G
button
to select “OTHER SETUP”.
+
Press the ENTER button to display
the “OTHER SETUP” menu, and
then press the
F
or
G
button to
select “LAMP RUNTIME”
.
,
Press and hold the ENTER button
for approximately 3 seconds
.
The “LAMP TIME RESET” screen
will be displayed.
-
Select “OK” by pressing the
I
or
H
button on the remote
control unit and then press the
ENTER button.
The “POWER OFF” confirmation
screen will be displayed.
.
Press the POWER button to
turn off the power.
/
Disconnect the power cord
after the POWER button on the
projector illuminates red.
This will reset the cumulative
usage time for the lamp unit to “0”.
MENU
PICTURE ADJUSTMENT
POSITION ADJUSTMENT
OTHER SETUP
LANGUAGE SETUP
SECURITY SETUP
SD PICTURE SETUP
SELECT
ENTER
EXIT
NOTE:
B
Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not securely
installed, it may cause the
protection circuit to operate so
that the power cannot be turned
on.
NOTE:
B
The “POWER OFF” screen will
disappear in five seconds.
B
If the MENU button is pressed, the
“LAMP TIME RESET” screen and
the “POWER OFF” confirmation
screen will be cancelled.
NOTE:
B
If the power cord was
disconnected during projection
when the projector was used
the last time, projection will
start after the power cord is
connected.
Lamp unit replacement procedure
#
Disconnect the power cord
from the projector by following
the procedure on page 28, and
check that the area around the
lamp unit has cooled down.
$
Use a Phillips screwdriver to
turn the lamp unit cover fixing
screw at the bottom of the
projector, and then remove the
lamp unit cover.
%
Use a Phillips screwdriver to
loosen the lamp unit fixing
screw until the screw turns
freely. Then hold the handle of
the lamp unit and gently pull the
lamp unit out from the projector.
&
Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screw.
When inserting the new lamp unit, be
sure to push it in at the point
A
and
B
.
LAMP indicator
On-screen display
Illuminates red during
image projection and
standby mode.
Displayed for 30
seconds. Pressing any
button will clear the
display.
More than 2 250 hours
Remains displayed until
any button is pressed.
More than 2 500 hours
NOTE:
B
If the lamp usage time has passed 2 500 hours, the projector will switch to
standby mode after approximately 10 minutes of operation. The steps
)
to
/
on the next page should thus be completed within 10 minutes.
Handle
Lamp unit cover
Lamp unit cover fixing screw
Lamp unit fixing screw
OTHER SETUP
AUTO SIGNAL
ON
TV-SYSTEM
AUTO
FRONT/REAR
FRONT
DESK/CEILING
DESK
HIGHLAND
OFF
LAMP RUNTIME
2300H
SXGA MODE
SXGA
CTRL PANEL
VALID
NR
OFF
SELECT
RETRN
LAMP TIME RESET
OK
CANCEL
POWER OFF
[POWER] OK
Care and maintenance