Panasonic PT-52LCX65 Multi Media Display - Page 7

Getting Started, Emergency Alert System EAS, Forced Tuning, Remote Control Battery Installation

Get Panasonic PT-52LCX65 - 52inch Rear Projection TV PDF manuals and user guides
UPC - 037988975341
View all Panasonic PT-52LCX65 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Getting Started Remote Control Battery Installation Requires two AA batteries (supplied). 1. While pressing in on the catch, open cover in direction of arrow. Helpful Hints: (1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life. (2) Whenever you remove the batteries, you may need to reset the remote control infrared codes. We recommend that you record the code on pages 58-59, prior to setting up the remote. 2. Install the batteries as shown in the battery compartment. (Polarity + or - must match the markings in the compartment). Two AA size 3. Press cover in direction of arrow until it snaps shut. Emergency Alert System (EAS) Forced Tuning If a CableCARD™ is installed, the cable MSO (multiple system owner/operator) may provide an Emergency Alert System message. These messages are intended to alert the general public of important local or national emergency situations. In the event of receipt of one of these messages, the Projection Display shall immediately tune to the channel as directed by the EAS message. If the channel has been blocked using the parental control, the parental blocking has priority over the forced tune. CAUTION Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote control. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Projection Display set. Reset All Memory Functions Use when moving unit to a new location, or First Time Setup needs to be redone. CH VOL OK VOL CH Press the VOL- button on the unit and OK button on the Remote control at the same time for more than 3 seconds. When reset is done, power shuts off automatically. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
7
Getting Started
Emergency Alert System (EAS)
Forced Tuning
If a CableCARD™ is installed, the cable
MSO
(multiple system owner/operator) may provide an
Emergency Alert System message. These messages
are intended to alert the general public of important
local or national emergency situations. In the event
of receipt of one of these messages, the Projection
Display shall immediately tune to the channel as
directed by the EAS message. If the channel has
been blocked using the parental control, the parental
blocking has priority over the forced tune.
Requires two AA batteries (supplied).
2
.
Install the batteries as shown in the battery
compartment.
(Polarity + or - must match the markings in the
compartment).
Two AA size
Remote Control Battery Installation
CAUTION
1
.
While pressing in on the catch, open cover in
direction of arrow.
3
.
Press cover in direction of arrow until it snaps
shut.
Incorrect battery installation can cause the batteries to
leak, leading to personal injury and/or damage to the
remote control.
Observe the following precautions:
1.
Batteries should always be replaced as a pair.
Always use new batteries when replacing the old
set.
2.
Do not combine a used battery with a new one.
3.
Do not mix battery types (example: “Zinc Carbon”
with “Alkaline”).
4.
Do not attempt to charge, short-circuit, disassemble,
heat or burn used batteries.
5.
Battery replacement is necessary when the remote
control acts sporadically or stops operating the
Projection Display set.
Helpful Hints:
(1) For frequent remote control users, replace old
batteries with Alkaline batteries for longer battery
life.
(2) Whenever you remove the batteries,
you may
need to reset the remote control infrared
codes
. We recommend that you record the code
on pages 58-59, prior to setting up the remote.
Reset All Memory Functions
Use when moving unit to a new location, or First Time
Setup needs to be redone.
Press the VOL- button on the unit
and OK button on the Remote
control at the same time for more
than 3 seconds. When reset is done,
power shuts off automatically.
CH
CH
VOL
VOL
OK