Panasonic PT-F300EA Operating Instructions - Page 52

Care and Replacement, Replacement procedure, Resetting the REMAINING, FILTER, ENGLISH - 52

Get Panasonic PT-F300EA PDF manuals and user guides View all Panasonic PT-F300EA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Care and Replacement J Replacement procedure 1. Turn the projector upside down and place it gently on a soft cloth. 2. Use a Phillips-head screwdriver to loosen 3 ACF cover fixing screws until the screws turn freely and remove the ACF cover. ACF cover fixing screw J Resetting the REMAINING FILTER 1. Turn on the projector and display the FILTER COUNTER RESET in PROJECTOR SETUP. 2. Press the ENTER button for more than 3 seconds. The confirmation screen will be displayed. 3. Select OK by pressing I, then press the ENTER button. 4. Display the STATUS and confirm the figure. Soft cloth ACF cover 3. Release the lock by pushing in the lock clamp to inside, and slide out the ACF unit from the projector slowly. 4. Insert the new ACF unit into the compartment in correct direction and slightly push down until it clicks. Tighten an ACF fixing screw securely with a Phillips-head screwdriver. 5. Attach the ACF cover and tighten the ACF cover fixing screws securely with a Phillips-head screwdriver. Push in ACF FILTER COUNTER RESET RESET FILTER COUNTER? OK SELECT CANCEL RETURN ENTER Push in Clamp NOTE: • If the ACF and/or ACF cover are attached incorrectly, the projector may not be turned on. • Do not switch the power on while the ACF cover removed. • When you replace the ACF unit, clean the compartment and/or the air exhaust port if you need to. Maintenance ENGLISH - 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Maintenance
Care and Replacement
E
NGLISH - 52
Replacement procedure
1.
Turn the projector upside down and place it gently
on a soft cloth.
2.
Use a Phillips-head screwdriver to loosen 3 ACF
cover fixing screws until the screws turn freely and
remove the ACF cover.
3.
Release the lock by pushing in the lock clamp to
inside, and slide out the ACF unit from the
projector slowly.
4.
Insert the new ACF unit into the compartment in
correct direction and slightly push down until it
clicks. Tighten an ACF fixing screw securely with a
Phillips-head screwdriver.
5.
Attach the ACF cover and tighten the ACF cover
fixing screws securely with a Phillips-head
screwdriver.
Resetting the REMAINING
FILTER
1.
Turn on the projector and display the
FILTER
COUNTER RESET
in
PROJECTOR SETUP
.
2.
Press the
ENTER
button for more than 3 seconds.
The confirmation screen will be displayed.
3. Select
OK
by pressing
I
, then press the
ENTER
button.
4.
Display the
STATUS
and confirm the figure.
NOTE:
•
If the ACF and/or ACF cover are attached incorrectly,
the projector may not be turned on.
•
Do not switch the power on while the ACF cover
removed.
•
When you replace the ACF unit, clean the compartment
and/or the air exhaust port if you need to.
ACF cover
ACF cover fixing screw
Soft cloth
Clamp
ACF
Push in
Push in
RESET FILTER COUNTER?
OK
CANCEL
SELECT
ENTER
RETURN
FILTER COUNTER RESET