Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector Operat - Page 134

[standby Mode], [no Signal Shut-off], [no Signal Lights-out], To Select [no Signal Shut-off].

Get Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector PDF manuals and user guides View all Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Chapter 4 Settings - [PROJECTOR SETUP] menu 12) Adjust [LIGHT OUTPUT] of each projector. ffAdjust [LIGHT OUTPUT] of all the other projectors so that the brightness will be the same as the projector with the least brightness. 13) Set [CONSTANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] in all projectors. 14) Select [APPLY] of [BRIGHTNESS CONTROL SETUP] and press the button in all projectors. ffBrightness control starts. Note ff Brightness is automatically corrected whenever the light source lights up by switching on/off the projector, etc. ff When the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the brightness control. [STANDBY MODE] Set the power consumption during the standby. 1) Press as to select [STANDBY MODE]. 2) Press qw to switch the item. ffThe items will switch each time you press the button. [NORMAL] [ECO] Select this item to use the network function during standby. Select this item to reduce power consumption during standby. Note ff The AC voltage monitor function, the network function, the terminal, and part of the RS‑232C command cannot be used during the standby when set to [ECO]. When an error or warning occurs on the projector, the self-diagnosis display appears on the control panel regardless of the [STANDBY MODE] settings. (x page 189) ff When [ECO] is set, it may take approximately 10 seconds longer before the projector starts projecting after the power is turned on, compared with when [NORMAL] is set. ff When [NORMAL] is set, the network function and the terminal can be used during standby. ff The [STANDBY MODE] setting will not reset to the factory default even if [ALL USER DATA] is executed from the [PROJECTOR SETUP] menu → [INITIALIZE]. [NO SIGNAL SHUT-OFF] A function that automatically switches the power source of the projector to standby if there is no input signal for a certain period of time. The time before switching to standby can be set. 1) Press as to select [NO SIGNAL SHUT-OFF]. 2) Press qw to switch the item. ffThe items will switch each time you press the button. [DISABLE] [10MIN.] - [90MIN.] Disables the No signal shut-off function. Sets the time in increments of 10 minutes. [NO SIGNAL LIGHTS-OUT] This is a function to automatically turn off the light source of the projector when there is no input signal for specific period. The time until the light source is turned off can be set. 1) Press as to select [NO SIGNAL LIGHTS-OUT]. 2) Press qw to switch the item. ffThe items will switch each time you press the button. [DISABLE] [10SEC.] - [5MIN.] Disables the no signal lights-out function. Turns off the light source when there is no input signal for the preset period. Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.]. 134 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
Chapter 4
Settings — [PROJECTOR SETUP] menu
134 - ENGLISH
12) Adjust [LIGHT OUTPUT] of each projector.
f
Adjust [LIGHT OUTPUT] of all the other projectors so that the brightness will be the same as the projector
with the least brightness.
13)
Set [CONSTANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] in
all projectors.
14) Select [APPLY] of [BRIGHTNESS CONTROL SETUP] and press the <ENTER> button in all projectors.
f
Brightness control starts.
Note
f
Brightness is automatically corrected whenever the light source lights up by switching on/off the projector, etc.
f
When the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the
brightness control.
[STANDBY MODE]
Set the power consumption during the standby.
1)
Press
as
to select [STANDBY MODE].
2)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[NORMAL]
Select this item to use the network function during standby.
[ECO]
Select this item to reduce power consumption during standby.
Note
f
The AC voltage monitor function, the network function, the <SERIAL OUT> terminal, and part of the RS-232C command cannot be used
during the standby when set to [ECO].
When an error or warning occurs on the projector, the self-diagnosis display appears on the control panel regardless of the [STANDBY
MODE] settings. (
x
page 189)
f
When [ECO] is set, it may take approximately 10 seconds longer before the projector starts projecting after the power is turned on,
compared with when [NORMAL] is set.
f
When [NORMAL] is set, the network function and the <SERIAL OUT> terminal can be used during standby.
f
The [STANDBY MODE] setting will not reset to the factory default even if [ALL USER DATA] is executed from the [PROJECTOR SETUP]
menu
→
[INITIALIZE].
[NO SIGNAL SHUT-OFF]
A function that automatically switches the power source of the projector to standby if there is no input signal for a
certain period of time. The time before switching to standby can be set.
1)
Press
as
to select [NO SIGNAL SHUT-OFF].
2)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[DISABLE]
Disables the No signal shut-off function.
[10MIN.] - [90MIN.]
Sets the time in increments of 10 minutes.
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn off the light source of the projector when there is no input signal for specific
period. The time until the light source is turned off can be set.
1)
Press
as
to select [NO SIGNAL LIGHTS-OUT].
2)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[DISABLE]
Disables the no signal lights-out function.
[10SEC.] - [5MIN.]
Turns off the light source when there is no input signal for the preset period.
Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.].