Panasonic PV GS400 Digital Video Camcorder - Page 68

To Disconnect Usb Cable Safety, If You No Longer Need Software Or Driver (uninstall) - drivers

Get Panasonic PV GS400 - 4MP 3CCD MiniDV Camcorder PDF manuals and user guides
UPC - 037988977772
View all Panasonic PV GS400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

With a PC 7 Double click [PhotoImpression Installer] (or [PhotoBase Installer] or [PanoramaMaker Installer] or [PhotoPrinter Installer]). 8 Follow the instructions on the computer screen until the installation is complete. ª To start software in ArcSoft Software Suite 1 Select [Start] >> [All Programs (Programs)] >> [ArcSoft Software Suite] >> [Panorama Maker 3] (or [PhotoBase 4] or [PhotoImpression 4] or [PhotoPrinter 4]). Note on the driver name displayed The driver name displayed will differ depending on your OS, operating environment and the mode of the Camcorder. ≥Some Operating Systems, such as Windows 98SE, may not show the icon indicating that you may safely disconnect in task tray. (OS may be set not to show.) Make sure Camcorder's Card Access Lamp is off and disconnect the cable. Also, with Windows Me, the icon will not be displayed when in Tape Recording Mode or Tape Playback Mode. CAUTION: If you disconnect the USB Cable while the Card Access Lamp is on, it may damage the Card data. For Information on ArcSoft Software: TEL: 1-510-440-9901 Website: www.arcsoft.com Refer to Help information about application operations and other Error messages. To disconnect USB Cable safely If USB Cable is disconnected while computer is on, error dialog box may appear. In such a case click [OK] and close the dialog box. By following the steps below you can disconnect the cable safely. 1 Double click the icon in task tray. ≥Hardware disconnect dialog box appears. O If the above operation is not performed correctly, when data is copied from the personal computer to an SD Memory Card, the copied data may be damaged. When the following operations are performed, the same results will occur as when the USB Cable is incorrectly removed (above). Therefore, it is imperative that the above operation is completed before proceeding. ≥When SD Memory Card is removed. ≥When Camcorder power is turned OFF. ON FF ≥When Mode Dial (44) is turned to change modes. 2 Select [USB Mass Storage Device] and click [Stop]. 3 Verify [Matshita DVC USB Device] is selected and click [OK]. ≥You can safely disconnect the cable. S (44) If you no longer need software or driver (Uninstall) The screens may vary with the type of OS. 1 Select [Start] (>> [Settings]) >> [Control Panel], select the software or the driver from [Add/Remove Programs] to uninstall. ≥Uninstalling steps may vary depending on the OS. Please refer to the user manual of your OS. D PC 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
With a PC
68
7
Double click [PhotoImpression Installer] (or
[PhotoBase Installer] or
[PanoramaMaker Installer] or
[PhotoPrinter Installer]).
8
Follow the instructions on the computer
screen until the installation is complete.
ª
To start software in ArcSoft Software
Suite
1
Select [Start] >> [All Programs (Programs)]
>> [ArcSoft Software Suite] >>
[Panorama Maker 3] (or [PhotoBase 4] or
[PhotoImpression 4] or [PhotoPrinter 4]).
Refer to Help information about application
operations and other Error messages.
To disconnect USB Cable safely
If USB Cable is disconnected while computer is
on, error dialog box may appear. In such a case
click [OK] and close the dialog box. By following
the steps below you can disconnect the cable
safely.
1
Double click the
icon in task tray.
≥
Hardware disconnect dialog box appears.
2
Select [USB Mass Storage Device] and click
[Stop].
3
Verify [Matshita DVC USB Device] is
selected and click [OK].
≥
You can safely disconnect the cable.
For Information on ArcSoft Software:
TEL:
1-510-440-9901
Website:
www.arcsoft.com
Note on the driver name displayed
The driver name displayed will differ depending
on your OS, operating environment and the mode
of the Camcorder.
≥
Some Operating Systems, such as Windows
98SE, may not show the icon indicating that you
may safely disconnect in task tray. (OS may be
set not to show.) Make sure Camcorder’s Card
Access Lamp is off and disconnect the cable.
Also, with Windows Me, the icon will not be
displayed when in Tape Recording Mode or
Tape Playback Mode.
If the above operation is not performed correctly,
when data is copied from the personal computer
to an SD Memory Card, the copied data may be
damaged.
When the following operations are performed, the
same results will occur as when the USB Cable is
incorrectly removed (above). Therefore, it is
imperative that the above operation is completed
before proceeding.
≥
When SD Memory Card is removed.
≥
When Camcorder power is turned OFF.
≥
When Mode Dial
(44)
is turned to change
modes.
If you no longer need software or
driver (Uninstall)
The screens may vary with the type of OS.
1
Select [Start] (>> [Settings]) >>
[Control Panel], select the software or the
driver from [Add/Remove Programs] to
uninstall.
≥
Uninstalling steps may vary depending on the
OS. Please refer to the user manual of your OS.
CAUTION:
If you disconnect the USB Cable while the
Card Access Lamp is on, it may damage the
Card data.
O
F
F
ON
PC
S
D
(44)