Panasonic PVHS3000 PVHS3000 User Guide - Page 44

Learning the Codes Programmed Into the Remote, Re-assigning Component Mode, Buttons

Page 44 highlights

Universal Remote Control (continued) Learning the Codes Programmed Into the Remote If you set up the Hard Disk Recorder remote by following "Searching for Your Component's Code" on page 43, you may want to figure out which four-digit code is operating your equipment. Use this procedure after you set up your components to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV after setting up your TV, follow steps below. 1 Press TV. 2 Hold down CODE SET until the remote's red LED blinks twice, then release. 3 Press 9 - 9 - 0. 4 Learn your code. 1) For the first digit of your four-digit code, press 1 and count the number of times the red LED blinks on the remote. 2) For the second digit, press 2 and count the number of times the red LED blinks on the remote. 3) For the third digit, press 3 and count the number of times the red LED blinks on the remote. 4) For the fourth and final digit, press 4 and count the number of times the red LED blinks on the remote. • If the LED does not blink, the digit is zero. Red LED 2 CODE SET a c VCR/DVD SAT/CABLE 1 TV 3 Number 4 buttons b NOTE • To find out the code for your other components, repeat steps 1~4, and substitute the appropriate device button (TV, SAT/ CABLE, or VCR/DVD) for the component code you wish to learn. Re-assigning Component Mode Buttons You can program the Hard Disk Recorder remote component mode buttons (TV, SAT/CABLE, or VCR/DVD) to control other home entertainment components. For example, to control a TV, a cable box, and a DVD player, you will need to re-assign the VCR button to operate the DVD player, follow the steps below. a Hold down CODE SET until the remote's red LED blinks twice, then release. b Press 9 - 9 - 2. The red LED will blink twice. c Press VCR/DVD twice. The red LED will blink twice. You can now program the VCR/DVD button for your DVD player. d See "Setting Up Your Components" on page 42. To reassign other component mode buttons... Repeat steps a~d by substituting the button sequence from the list of popular components at right. 44 Reassigning device keys TV as 2nd Press: CODE SET VCR button 9-9-2-VCR-TV TV as 2nd Press: CODE SET CABLE button 9-9-2-CABLE-TV TV back to TV Press: CODE SET 9-9-2-TV-TV VCR as 2nd TV button Press: CODE SET 9-9-2-TV-VCR VCR as 2nd Press: CODE SET CABLE button 9-9-2-CABLE-VCR VCR back to VCR Press: CODE SET 9-9-2-VCR-VCR PanaHDR- P42-.p65 44 00/12/01, 16:40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

44
Universal Remote Control
(continued)
Learning the Codes Programmed Into the Remote
If you set up the Hard Disk Recorder remote by following “Searching for Your
Component’s Code” on page 43, you may want to figure out which four-digit
code is operating your equipment. Use this procedure after you set up your
components to find out which four-digit code is operating your equipment.
For example, to find out which code is operating your TV after setting up
your TV, follow steps below.
Learn your code.
1)
For the first digit of your four-digit code, press
1
and
count the number of times the red LED blinks on the
remote.
2)
For the second digit, press
2
and count the number
of times the red LED blinks on the remote.
3)
For the third digit, press
3
and count the number of
times the red LED blinks on the remote.
4)
For the fourth and final digit, press
4
and count the
number of times the red LED blinks on the remote.
• If the LED does not blink, the digit is zero.
Hold down
CODE SET
until the remote’s red
LED blinks twice, then release.
2
Press
TV
.
1
Press
9
-
9
-
0.
3
4
NOTE
• To find out the code for your other components, repeat steps
1~4, and substitute the appropriate device button (
TV
,
SAT/
CABLE
, or
VCR/DVD
) for the component code you wish to learn.
Re-assigning Component Mode
Buttons
You can program the Hard Disk Recorder remote component mode
buttons (
TV
,
SAT/CABLE
, or
VCR/DVD
) to control other home
entertainment components.
For example, to control a TV, a cable box, and a DVD player, you will need to
re-assign the VCR button to operate the DVD player, follow the steps below.
Hold down
CODE SET
until the remote’s red
LED blinks twice, then release.
a
Press
9
-
9
-
2.
The red LED will blink twice.
b
You can now program the
VCR/DVD
button for your DVD player.
See “Setting Up Your Components” on page 42.
d
Press
VCR/DVD
twice.
The red LED will blink twice.
c
To reassign other component mode buttons...
Repeat steps a~d by substituting the button sequence from
the list of popular components at right.
TV as 2nd
VCR button
TV as 2nd
CABLE button
TV back to TV
VCR as 2nd
TV button
VCR as 2nd
CABLE button
VCR back to VCR
Reassigning device keys
Press: CODE SET
9-9-2-VCR-TV
Press: CODE SET
9-9-2-CABLE-TV
Press: CODE SET
9-9-2-TV-TV
Press: CODE SET
9-9-2-TV-VCR
Press: CODE SET
9-9-2-CABLE-VCR
Press: CODE SET
9-9-2-VCR-VCR
Red LED
CODE SET
VCR/DVD
c
SAT/CABLE
TV
1
Number
buttons
2
a
3
4
b
PanaHDR- P42-.p65
00/12/01, 16:40
44