Panasonic SA-XR50S SAXR50 User Guide - Page 14
OPERATIONS, CONTROL GUIDE, Main unit, Display
View all Panasonic SA-XR50S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Control guide Main unit Standby indicator [^] When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. [POWER 8] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. [SPEAKERS, A, B] For selecting speakers A or B. Turning the speakers off automatically engages the STEREO/2CH mode (when listening through headphones, for example). [% DIGITAL EX, % DIGITAL, % PL Ⅱ , DTS 96/24, DTS-ES, DTS, DTS NEO:6] Lights to indicate the source's input signal and decoding format used. % DIGITAL EX: Dolby Digital Surround EX sources % DIGITAL: Dolby Digital sources % PL Ⅱ : Dolby Pro Logic Ⅱ decoder is being used DTS 96/24: DTS 96/24 sources DTS-ES: DTS-ES discrete or matrix sources DTS: DTS sources DTS NEO:6: DTS NEO:6 matrix decoder is being used [MULTI CONTROL] Press to enter Multi control mode, and use [INPUT SELECTOR] to select/ enter. [INPUT SELECTOR] For selecting input. Selects/Enters each setting in Multi control mode. [VOLUME] Volume control. Remote control signal sensor ^ POWER 8 SPEAKERS A B 6.1CH DECODING VCR 2 VIDEO IN L AUDIO IN R MULTI CONTROL INPUT SELECTOR PUSH ENTER VOLUME DOWN UP PHONES [VCR 2] For a video camera, etc. [6.1CH DECODING] For turning on the 6.1 channel decoding mode. When using this mode the indicator lights. [BASS SYNTHESIZER] For turning on the bass synthesizer mode. When using this mode the indicator lights. [MULTI-SOURCE RE-MASTER] For selecting a re-master mode. When using this mode the indicator lights. [TUNE 2, 1] For tuning the radio and selecting preset stations. Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. [PHONES] Headphone jack Plug type: 6.3 mm (1/4") stereo • Avoid listening for prolonged periods of time to prevent hearing damage. • Turn the speakers off when using the headphones. Display • When you turn the dimmer to "ON", the following indicators change to dim. [- SPEAKERS Speaker indicators :Sound is output from speakers connected to the front A, surround, and center terminals. : Sound is output only from speakers connected to the front B terminals. :Sound is output from speakers connected to the front A and B terminals. [TUNED, ST, , MONO] Radio indicators TUNED: A station is tuned. ST: A stereo FM broadcast is tuned. : Flashes during automatic presetting. MONO: Lights when using the monaural mode. [SLEEP] Sleep timer indicator. [SFC, CENTER FOCUS, 2CH MIX, MULTI REAR] SFC: Lights when using an SFC mode. CENTER FOCUS: Lights when using the center focus mode. 2CH MIX: Lights when playing a multi- channel source in 2CH MIX mode. MULTI REAR: Lights when using the multi rear surround mode. [] When you press the [MULTI CONTROL] button and enter the settings the indicator lights. [-DIGITAL INPUT-, L, C, R, S, LS, SB, RS, LFE] Program format indicators Show the channels contained in the digital input signal. They do not light when input is analog. L: Front left channel C: Center channel R: Front right channel S: If the surround channel is monaural. LS: Surround left channel SB: Surround back channel RS: Surround right channel LFE (Low Frequency Effects): Deep-bass effect. Operations RQT7487 [TAPE MONITOR] Lights when the tape monitor is on. General display Shows the input mode, radio frequency, and other general information. 14 SPEAKERS AB TAPE MONITOR TUNED ST M MONO SLEEP SFC CENTER FOCUS 2CH MIX MULTI REAR MULTI CONTROL DIGITAL INPUT L CRS LS SB RS LFE DIGITAL PROCESSING fs kHz MHz kHz [DIGITAL PROCESSING fs] Displays the frequency the unit is processing. [kHz, MHz] Frequency unit indicators kHz: AM, or PCM sampling frequency MHz: FM