Panasonic SAHT790V SAHT790V User Guide - Page 58
Recording, Listening to the radio, Unit display, Television display, On-Screen Menu Icons
View all Panasonic SAHT790V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 58 highlights
Troubleshooting guide Recording "1" flashes when I try to start ≥If the erasure prevention tab has been removed, cover the hole with adhesive tape. 5 recording. Cannot record. Timer recording doesn't record a ≥Check the clock and calendar. - program correctly. ≥Set the channel and start and end times correctly. - ≥Be sure to press [F] after programming to put the unit in timer recording standby. 38 ≥Program times may be overlapped. - Cannot record from other ≥Press [3 CHW] or [4 CHX] to Select "AU". 37 equipment. ≥Check the connections to the other equipment. 37 Black bands appear in the ≥Move the other equipment away from the television as it may be picking up interference. - recording. The copy of a videotape or DVD is ≥This unit complies with industry standards regarding the recording and duplication of copy- - very poor. protected material. This includes commercial videotapes and DVDs. Consequently, copying not only infringes copyright laws but also presents serious technical difficulties. Even in cases where a copy can be made, the quality will be very poor. Listening to the radio Cannot select the tuner ≥Check and see if the subwoofer's AC power supply cord is connected. 14 Noise is heard. ≥Adjust the position of the FM or AM antenna. - "ST" flickers or doesn't light. ≥Use an outdoor antenna. 47 Sound is distorted. A beat sound is heard. ≥Turn the television off or separate it from the unit. - A low hum is heard during AM ≥Separate the antenna from other cables and cords. - broadcasts. Unit display The unit's display disappears or ≥The DISPLAY setting is set to "DIM" or "OFF" under OPTION from the VCR MENU. Select 44 fades once the power is turned off. "BRIGHT" if you want the display bright all the time. The tape counter isn't changing. ≥The tape counter does not change while playing unrecorded parts. - "No PLAY" "No DISC" "F61" "U11" "ERROR" "H∑∑", "F∑∑" ∑∑ stands for a number. ≥The display also appears like this if the tape is dirty or damaged. Consult your dealer if this is the case. ≥You inserted a disc the unit cannot play; insert one it can. ≥You inserted a blank DVD-RAM. ≥You haven't inserted a disc; insert one. ≥You haven't inserted the disc correctly; insert it correctly. ≥Check and correct the speaker cord connections. If this does not fix the problem, there is a power supply problem. Consult the dealer. ≥Disc is dirty. Wipe it clean. ≥Incorrect operation performed. Read the instructions and try again. ≥Trouble may have occurred. The number following "H" or "F" depends on the status of the unit. Reset procedure: Press [Í] to switch the unit to the standby mode and then back to ON. Alternatively, press [Í] to switch the unit to the standby mode, disconnect both AC power supply cords, and then reconnect. ≥If the service numbers fail to clear, note the service number and contact a qualified service person. - 6 - - 18 11, 14 6 - - - Television display "Cannot display group xx, picture ≥You are trying to display incompatible pictures. - xx" No on-screen display. ≥Go to Display in the SETUP menus, and select "On" for "On-Screen Messages". 31 ≥Go to OPTION in the VCR MENU, and select "ON" for "OSD". 44 On-Screen Menu Icons not ≥Press [3, 4] while the rightmost icon is highlighted to move them down. 28 displayed or only partially displayed on the television. The menu is displayed in a ≥Go to Disc in the SETUP menus, and select the preferred language for "Menus". 31 different language. ≥Go to LANGUAGE in the VCR MENU, and select the preferred language for menus. 42 RQT6951 58