Panasonic SC-PM700 Owners Manual - Page 10

Sound effects

Get Panasonic SC-PM700 PDF manuals and user guides View all Panasonic SC-PM700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

█ Selecting a preset station 1 Press [PLAY MENU] repeatedly to select "TUNE MODE". 2 Press [R, T] to select "PRESET" and then press [OK]. 3 Press [2/3] or [5/6] to select the preset station. Improving the sound quality 1 Press [PLAY MENU] repeatedly to select "FM MODE". 2 Press [R, T] to select "MONO" and then press [OK]. To cancel, select "STEREO". "MONO" is also canceled when you change the frequency. To memorize the setting Continue with step 4 of "Manual presetting". Checking the signal status Press [DISPLAY]. FM - - - - FM ST FM MONO The FM signal is weak. The system is not tuned in to a station. The FM signal is in stereo. "MONO" is selected as the "FM MODE". The FM signal is in monaural. FM allocation setting This system can also receive FM broadcasts allocated in 0.1 MHz steps. 1 Press [RADIO]. 2 Press [PLAY MENU] repeatedly to select "FREQ.STEP". 3 Press [R, T] to select "100kHz" and then press [OK]. After a few seconds, the display panel shows the current minimum radio frequency. • To go back to the initial setting, do the above steps again and select "200kHz" in step 3. • Preset frequencies are erased after you change the setting. Sound effects 1 Press [SOUND] repeatedly to select the sound effect. 2 Press [R, T] to select the setting and then press [OK]. MY SOUND PRESET EQ BASS TREBLE D.BASS SURROUND "SOUND 1", "SOUND 2" or "SOUND 3" "HEAVY" (default), "SOFT", "CLEAR", "VOCAL" or "FLAT" -4 to +4 (default: 0) Using the main unit Turn [BASS]. -4 to +4 (default: 0) Using the main unit Turn [TREBLE]. "ON D.BASS" (default) or "OFF D.BASS" "ON SURROUND" or "OFF SURROUND" (default) Note: Changed settings will be kept until it is changed again, unless otherwise indicated. Saving the sound settings You can save the current sound effects (up to 3 combinations). Preparation Select the sound effects. 1 Press [SETUP] to select "SAVE MY SOUND". 2 Press [R, T] to select a sound setting number and then press [OK]. "SAVED" is shown. The new setting replaces the one existing in the same sound setting number. To recall the setting 1 Press [SOUND] to select "MY SOUND". 2 Press [R, T] to select the sound setting number and then press [OK]. TQBM0873 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
10
TQBM0873
█
Selecting a preset station
1
Press [PLAY MENU] repeatedly to select
“TUNE MODE”.
2
Press [
R
,
T
] to select “PRESET” and then press
[OK].
3
Press [
2
/
3
] or [
5
/
6
] to select the preset
station.
Improving the sound quality
1
Press [PLAY MENU] repeatedly to select
“FM MODE”.
2
Press [
R
,
T
] to select “MONO” and then press
[OK].
To cancel, select “STEREO”.
“MONO” is also canceled when you change the
frequency.
To memorize the setting
Continue with step 4 of “Manual presetting”.
Checking the signal status
Press [DISPLAY].
FM allocation setting
This system can also receive FM broadcasts allocated in
0.1 MHz steps.
1
Press [RADIO].
2
Press [PLAY MENU] repeatedly to select
“FREQ.STEP”.
3
Press [
R
,
T
] to select “100kHz” and then press
[OK].
After a few seconds, the display panel shows the current
minimum radio frequency.
•
To go back to the initial setting, do the above steps
again and select “200kHz” in step 3.
•
Preset frequencies are erased after you change the
setting.
Sound effects
1
Press [SOUND] repeatedly to select the sound
effect.
2
Press [
R
,
T
] to select the setting and then press
[OK].
Note:
Changed settings will be kept until it is changed again, unless
otherwise indicated.
Saving the sound settings
You can save the current sound effects (up to
3 combinations).
Preparation
Select the sound effects.
1
Press [SETUP] to select “SAVE MY SOUND”.
2
Press [
R
,
T
] to select a sound setting number and
then press [OK].
“SAVED” is shown.
The new setting replaces the one existing in the same
sound setting number.
To recall the setting
1
Press [SOUND] to select “MY SOUND”.
2
Press [
R
,
T
] to select the sound setting number
and then press [OK].
FM – – – –
The FM signal is weak.
The system is not tuned in to a station.
FM ST
The FM signal is in stereo.
FM MONO
“MONO” is selected as the “FM MODE”.
The FM signal is in monaural.
MY SOUND
“SOUND 1”, “SOUND 2” or “SOUND 3”
PRESET EQ
“HEAVY” (default), “SOFT”, “CLEAR”,
“VOCAL” or “FLAT”
BASS
–4 to +4 (default: 0)
Using the main unit
Turn [BASS].
TREBLE
–4 to +4 (default: 0)
Using the main unit
Turn [TREBLE].
D.BASS
“ON D.BASS” (default) or
“OFF D.BASS”
SURROUND
“ON SURROUND” or
“OFF SURROUND” (default)