Panasonic SCEN35 SCEN33 User Guide - Page 6

Timers and others ➡ Page 2 for the position of remote control buttons. Setting the time This is a 12-hour clock.  Press [CLOCK/TIMER] to set the clock.  Press [2/u] or [1/i] to select the time within 5 seconds. (Press and hold to change the time faster.)  Press [CLOCK/TIMER] again. g To display the clock when the unit is on Press [CLOCK/TIMER] g To check the time when the unit is off Press [CLOCK/TIMER] Note The clock is accurate to within ±60 seconds a month. Readjust if necessary. Set again after disconnecting the AC power supply cord or power failure. Sleep timer The SLEEP timer can turn the unit off after a set time. Press [SLEEP] to turn the SLEEP function ON/OFF. • Each time you press the button: 30 MIN 60 MIN 90 MIN OFF (Canceled) 120 MIN g To check the remaining time Press [SLEEP] once Note The play timer and sleep timer can be used together. The sleep timer always has priority. Be sure not to overlap timer settings. Sound quality You can choose one of four types of sound quality. Press [PRESET EQ] to select the sound quality. EQ • Each time you press the button: HEAVY (Adds punch to rock) CLEAR (Clarifies higher sounds) SOFT (For background music) EQ OFF (Canceled) VOCAL (Adds gloss to vocals) Live Virtualizer You can create a three-dimensional sound field when listening to stereo sound. Press [SURROUND] to turn the Live Virtualizer ON/OFF. Note The actual effect depends on the source played. Specifications Play timer You can set the timer to come on at a certain time to wake you up. Preparation: Turn the unit on and set the clock. Prepare the music source you want to listen to; disc, radio or music port source, and set the volume.  Press [CLOCK/TIMER] repeatedly to select play timer. CLOCK zPLAY Original display  "ON TIME" is displayed. Within 5 seconds, press [2/u] or [1/i] to set the starting time.  Press [CLOCK/TIMER] to confirm.  "OFF TIME" is displayed. Repeat steps 2 and 3 to set the finishing time. To activate the timer  Press [zPLAY] to turn on the timer.  Press [^] to turn off the unit. To Action Change the settings Repeat steps 1 to 4 and 6. Change the source of volume  Press [zPLAY] to clear zPLAY indicator from the display.  Make changes to the source or volume.  Perform steps 5 and 6. Check the settings (when the Press [CLOCK/TIMER] repeatedly to select unit is on or in standby mode) zPLAY. Cancel Press [zPLAY] to clear the timer indicator from the display. Note • The timer will start at the preset time, with the volume increasing gradually to the preset level. • The timer comes on at the set time every day if the timer is on. • The unit must be in the standby mode for the timer to function. • If you turn the unit off and on again while the timer is functioning, the finish time setting will not be activated. • When MUSIC PORT is selected as the source when the timer comes on, the system turns on and engages MUSIC PORT as the source. If you wish to playback from the portable audio equipment, activate the equipment's play mode and increase the volume. (See the portable audio equipment's instruction manual.) • When XM Satellite Radio is selected as the source and the timer comes on, the system will play the last XM channel tuned before power off. g AMPLIFIER SECTION FTC OUTPUT POWER both channel driven simultaneously 10 % total harmonic distortion (THD) 1 kHz SC-EN35 2.8 W per channel SC-EN33 1.8 W per channel RMS OUTPUT POWER both channel driven simultaneously 10 % total harmonic distortion (THD) 1 kHz SC-EN35 3 W per channel SC-EN33 2 W per channel Output impedance HEADPHONE 16 Ω to 32 Ω MUSIC PORT 14 kΩ DC IN Jack Terminal 14 V Phone Jack Terminal 3.5 mm stereo Music Port Jack Terminal 3.5 mm stereo XM Ready XM Connect & Play Antenna Only g TUNER SECTION Frequency range FM 87.9 MHz to 107.9 MHz (200 kHz) 87.5 MHz to 108.0 MHz (100 kHz) AM 520 kHz to 1710 kHz (10 kHz) Maintenance g CD SECTION Disc played [8 cm (3") or 12 cm (5")] (1) CD-Audio (CD-DA) (2) CD-R/RW (CD-DA, MP3) (3) MP3 Sampling frequency CD 44.1 kHz MP3 32 kHz, 44.1 kHz, 48 kHz Bit rate MP3 32 kbps to 384 kbps Decoding 16/20/24 bit linear Pick up Wavelength 785 nm Laser power CLASS 1 Audio Output (Disc) Number of channels 2 channel Frequency response 20 Hz to 20 kHz (+1, -2 dB) Wow and flutter Below measurement limit Digital filter 8 D/A converter MASH (1 bit DAC) g GENERAL Power supply AC 120 V, 60 Hz Power consumption SC-EN35 SC-EN33 30 W 16 W Dimensions (W x H x D) 220 mm x 236 mm x 146 mm (8 21/32" x 9 9/32" x 5 3/4") Mass With speakers SC-EN35 SC-EN33 3.62 kg (7.98 Ibs) 3.33 kg (7.34 Ibs) Without speakers SC-EN35 1.32 kg (2.91 Ibs) SC-EN33 1.26 kg (2.78 Ibs) Operating temperature range +5 °C to +35 °C (+41 °F to +95 °F) Operating humidity range 5 % to 90 % RH (no condensation) g SPEAKER SECTION Type 1 Way, 1 Speaker system Speaker Unit (s) Full range Speaker 8 cm (5 1/2") cone type 6 Ω Impedance 6 Ω Input power 6 W (MAX) Dimensions (W x H x D) 121 mm x 236 mm x 146 mm (4 3/4" x 9 9/32" x 5 3/4") Power consumption in standby mode:2.0 W (approx.) Notes: Specifications are subject to change without notice. Mass and dimensions are approximate. If the surfaces are dirty Care of the CD lens To clean this unit, wipe with a soft, dry cloth. • Clean the lens regularly to prevent malfunctions. Use a blower to remove dust and a • Never use alcohol, paint thinner or benzine to clean this unit. cotton swab if it is extremely dirty. 6 • Before using chemically treated cloth, read the instructions that came with the cloth Recommended product: Lens cleaner kit (part no. SZZP1038C). 7 carefully. • Do not use the lens cleaner of the CD type.