Panasonic SCHT810V SAHT790V User Guide - Page 46
RADIO & OTHERS, THE RADIO, Press [FM/AM] to select FM or
View all Panasonic SCHT810V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 46 highlights
The radio Í PLAY MODE DVD/VCR FM/AM REC DVD VCR TV TUNER RESET TV/VIDEO PAGE GROUP PICTURE MODE/ SETUP REPEAT PLAY MODE 1 4 7 100 SKIP 2 3 5 6 8 9 S10/ENTER 0 SLOW/SEARCH TV VOLj TV VOLi JET REW OPEN/CLOSE/EJECT FM/AM TUNER Numbered buttons 6 5 3CH W 4CH X ENTER VOLUME s r TOP MENU NAVI DIRECT NAVIGATOR CH MENU PLAY LIST ENTER OSD/DISPLAY RETURN CH VOLUME D.RE-MASTER C.S.M C.FOCUS S.POSITION SUBWOOFER SFC SUPER SRND MUTING POSITION MEMORY PROG [SHIFT] SUBTITLE CANCEL SLEEP ÎPL ZOOM QUICK REPLAY SPEED AUDIO TEST MIX 2CH CH SELECT Preparation ≥Press [TUNER] to put the remote control in TUNER mode. ≥Press [Í] to turn on the unit. ≥Press [FM/AM] to select "FM" or "AM" as the source. Manual tuning 1 Press [6] or [5] to select the frequency of the required station. TUNED: Displayed when a radio station is tuned. ST: Displayed when a stereo FM TUNEDST broadcast is being received. Press and hold [6] or [5] until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. 2 Adjust the volume. ∫ If noise is excessive in FM Press [PLAY MODE] to display "MONO". MONO Press [PLAY MODE] again to cancel the mode. The mode is also canceled when you change the frequency. ∫ FM frequency step The step is factory-set to 0.2 MHz, but you can change it to receive broadcasts allocated 0.1-MHz steps. 1 Press [FM/AM] to select "AM". 2 Press and hold [FM/AM]. After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed. To return to the original step, repeat the above steps. RQT6951 [Note] 46 Any FM and AM frequencies preset in channels will be initialized by this procedure. Preset them again. Preset tuning Preset channels to make selection simple. Up to 15 stations can each be set in the FM and AM bands. Automatic presetting 1 Tune to "FM 87.9" MHz or "FM 87.5" MHz (➡ left). 2 Press and hold [ENTER]. Release the button when "AUTO" is displayed. The tuner presets all the stations it can receive into the channels in ascending order. "SET OK" is displayed when the stations are set. The last station to be set is then played. 3 Tune to "AM 520" kHz. 4 Press and hold [ENTER]. "ERROR" is displayed Presetting was unsuccessful. Preset manually. Manual presetting 1 Tune to the station (➡ left). 2 Press [ENTER]. 3 While "PGM" is flashing Press the numbered buttons to select a channel. Alternatively, press [3 CHW] or [4 CHX] then press PGM [ENTER]. The station occupying a channel is erased if another station is preset in that channel. Selecting channels 1 Press [FM/AM] to select "FM" or "AM". 2 Press the numbered buttons or [3 CHW] or [4 CHX] to select the channel. To select a 2-digit number Example: To select channel 12, press [S10] ➡ [1] ➡ [2] [Note] The unit of display is MHz for FM radio and kHz for AM radio when the selector is in TUNER mode.