Panasonic SP-10 Owners Manual - Page 11

↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ Pitch control (fine adjustment to pitch) 1 Press [-] or [+] on the control unit to make adjustment. z The pitch can be set within approximately ±16% of the currently set turntable speed [33/45/78]. z The current set value appears on the display of the control unit. The display differs depending on the display mode. (Switching the display mode 21) z The turntable speed changes each time the pitch is set while the turntable is rotating. *Pressing the button increases or decreases the value. *Holding the button down accelerates the increase or decrease. „ When the display mode is "Turntable speed setting" The specified turntable speed 33 38.67 ・・ The adjusted value (turntable speed) z The value to two decimal places is displayed. z The turntable speed can be adjusted in increments of ±0.01 turn. [＋] ↑ 33 33.34 [＋] ↑ 33 33.33 [ー] 33 33.32 ・・ [ー] 33 28.00 „ When the display mode is "Pitch setting" The specified turntable speed 33 ＋ 16.0% ・・ The adjusted value (percentage) (Initial setting) [＋] ↑ 33 ＋ 0.1% [＋] ↑ 33 0.0% z The value to one decimal place is displayed. z The pitch can be adjusted in increments of ±0.1%. 20 (20) English [ー] 33 － 0.1% ・・ [ー] 33 － 16.0% „ To return to the prescribed turntable speed Press [RESET] on the control unit. The value immediately returns to the prescribed turntable speed. (331/3, 45 or 78.26 rpm) *The display of the control unit shows the prescribed setting. The turntable speed becomes the prescribed turntable speed in the turntable speed setting mode and 0.0% in the pitch setting mode. (Display mode: Turntable speed setting) 33 33.33 (Display mode: Pitch setting) 33 0.0% „ Speed selector button indicators of the main unit during pitch control STARTɾSTOP Indicators 33 45 78 z Blue LED on: Without pitch control (0.0%) z Orange LED on: During pitch control Note z The pitch can be set for each turntable speed. z Turning off the power button cancels the pitch control setting. Turning on the power button again returns the value to the initial setting. Playing back ↑ ↑ Operation and display of the control unit Turntable speed setting 1 Press [33/45/78] on the control unit. Each time [33/45/78] is pressed, the turntable speed changes in order of "33" → "45" → "78" → "33" → ... z The turntable speed changes each time the pitch is set while the turntable is rotating. 33 33.33 (331/3 turns) 45 45.00 (45 turns) 78 78.26 (78 turns) The specified turntable speed The adjusted value (turntable speed) Switching the display mode 1 Press [DISPLAY] on the control unit. Each time [DISPLAY] is pressed, the display mode changes in order of "turntable speed setting" → "Pitch setting" → "Turntable speed measurement" → "Turntable speed setting" → ... 33 33.33 (Turntable speed setting) 33 0.0% (Pitch setting) (Turntable 33 33.33 rpm speed measurement) (See below.) Turntablespeedmeasurement The actual turntable speed can be measured in this display mode. Switch the display mode (see above) to enter this mode. z "rpm" appears after the numerical value. z "--.-- rpm" appears when the turntable has stopped. 33 --.-- rpm (Stop state) 33 33.33 rpm (During rotation) „ Operation during "Turntable speed measurement" Operating the buttons as below changes the display mode to "Turntable speed setting" allowing you to make the setting. *The display mode returns to "Turntable speed measurement" if no operation is performed within three seconds. · [-]/[+]: The pitch can be adjusted. ( 20) · [RESET]: The value immediately returns to the prescribed turntable speed. · [33/45/78]: The turntable speed changes each time the button is pressed. Note z An averaged value is displayed. 21 (21) English