Panasonic SP-10 Owners Manual - Page 8

Putting the player together

Get Panasonic SP-10 PDF manuals and user guides View all Panasonic SP-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Getting started Putting the player together (continued) In order to prevent damage during shipping, some of the equipment has been disassembled. Put the player together in the following order. Attention z Do not connect the AC mains lead until set up is complete. z When fitting the turntable, prevent foreign material from getting in between the main unit and turntable. 4 Turntable mat 3 Mounting screw for turntable Belleville spring Washers Detachable handle mounting hole 2 Mount the turntable by aligning the rotor shaft fix hole (dotted line area in the figure below) located at the peak of the triangle with the rotor shaft marked with an arrow ( ). Be sure to check the figure below to not mix up the positional relationship of the turntable mounting holes. Handle carefully as this is heavy. 1 Turntable Detachable handle mounting hole 2 Rotor shaft fix hole Fitting the turntable 1 Tighten the detachable handle screws into the detachable handle mounting holes (two locations) on the turntable. Slowly lift the turntable and then lower it in such a way as to insert the center spindle into the hole in the center of the turntable. Attention z Tighten the detachable handle by turning it 5 or more times. If you have tightened it until the end, loose a little bit. Do not tighten it firmly. z Be careful when handling the turntable, as it is heavy. z Wipe off fingerprints or dirt with a soft cloth. 2 Slowly lower the turntable while aligning the rotor shaft fix holes (three locations) with the rotor shafts. z Mount by using the rotor shaft with the arrow mark as a guide. ( 14) 3 Attach the washers, belleville springs, and screws for turntable to the rotor shaft fix holes, and tighten the mounting screws securely. Mounting screw for turntable Belleville spring Washers Attention z When tightening screws, do not allow screw heads to protrude from the top surface of the turntable. z Tighten the three screws uniformly. Failing to do so may make the turntable rattle or rotate unstably. Make sure none of the screws are loose. „ To remove the turntable  Loosen the mounting screws for turntable and remove them. -Keep the screws, belleville springs, and washers carefully. ② Tighten the detachable handle screws into the detachable handle mounting holes (two locations) on the turntable and slowly lift the turntable straight up. Attention z If the rotor shafts are misaligned, a gap remains between the turntable and main unit and you cannot mount the turntable correctly. Do not force the turntable downward. Fitting the turntable mat 4 Lay the turntable mat on the turntable. Turntable Detachable handle mounting hole Rotor shaft Rotor shaft Centre spindle Attention z Do not use an electric screwdriver or impact wrench to tighten screws. z Note that using a screwdriver not fitting to the screws for mounting the turntable may damage the main unit. 14 (14) English 15 (15) English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Getting started
English
(14)
English
(15)
14
15
In order to prevent damage during shipping, some of the equipment has been disassembled.
Put the player together in the following order.
Attention
z
Do not connect the AC mains lead until set up is complete.
z
When fitting the turntable, prevent foreign material from getting in between the main unit and
turntable.
Attention
z
Do not use an electric screwdriver or impact wrench to tighten screws.
z
Note that using a screwdriver not fitting to the screws for mounting the turntable may damage
the main unit.
Putting the player together
(continued)
Turntable mat
4
Turntable
1
Handle carefully
as this is heavy.
Rotor shaft
Centre spindle
3
Mounting screw
for turntable
Belleville
spring
Washers
Rotor
shaft fix
hole
2
Mount the turntable by aligning the rotor
shaft fix hole (dotted line area in the figure
below) located at the peak of the triangle
with the rotor shaft marked with an arrow
(
). Be sure to check the figure below to
not mix up the positional relationship of the
turntable mounting holes.
Rotor shaft
Turntable
2
Detachable handle
mounting hole
Detachable handle
mounting hole
Detachable handle
mounting hole
Fitting the turntable
1
Tighten the
detachable
handle screws
into the
detachable
handle mounting
holes (two
locations) on the turntable. Slowly
lift the turntable and then lower it in
such a way as to insert the center
spindle into the hole in the center of
the turntable.
Attention
z
Tighten the detachable handle by turning it 5
or more times. If you have tightened it until the
end, loose a little bit. Do not tighten it firmly.
z
Be careful when handling the turntable, as it
is heavy.
z
Wipe off fingerprints or dirt with a soft cloth.
2
Slowly lower the turntable while aligning
the rotor shaft fix holes (three locations)
with the rotor shafts.
z
Mount by using the rotor shaft with the
arrow mark as a guide. (
14)
Attention
z
I
f the rotor shafts are misaligned, a gap
remains between the turntable and main unit
and you cannot mount the turntable correctly.
Do not force the turntable downward.
3
Attach the washers, belleville
springs, and screws for turntable to
the rotor shaft fix holes, and tighten
the mounting screws securely.
±
To remove the turntable
Loosen the mounting screws for turntable
and remove them.
-Keep the screws, belleville springs, and
washers carefully.
②
Tighten the detachable handle screws into
the detachable handle mounting holes (two
locations) on the turntable and slowly lift the
turntable straight up.
z
When tightening screws, do not allow screw
heads to protrude from the top surface of
the turntable.
z
Tighten the three screws uniformly. Failing
to do so may make the turntable rattle or
rotate unstably. Make sure none of the
screws are loose.
Attention
Mounting screw for
turntable
Belleville spring
Washers
Fitting the turntable mat
4
Lay the turntable mat on the
turntable.