Panasonic TH-85PB1U Operating Instructions - Page 25

Helpful Hint, Normalisation

Get Panasonic TH-85PB1U PDF manuals and user guides View all Panasonic TH-85PB1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Adjusting Pos./Size Clamp Position (During Component/PC input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) ĺ Value that causes least blackout is the optimum. When black parts are tinged with green ĺ Value that cancels the greenishness without causing blackout is the optimum. 1:1 Pixel Mode Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: • Select On when you would like to replay 1920 × 1080 input signal. • Applicable input signal; 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i • Select Off when Àickering is shown around the image. • H-Size and V-Size cannot be adjusted when On is selected. Off On 1:1 Pixel Mode When the input signal is a 2k1k signal (2048 × 1080 / 24p, 2048 × 1080 / 24sF), the display size (2k1k) is adjusted as follows. (For 2k1k signals) Off On (Left) On (Center) On (Right) Note: 2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. Helpful Hint ( / Normalise Normalisation) While the Pos./Size display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
25
Clamp Position
(During Component/PC input signal)
Adjusts the clamp position when black parts of the image have no detail due to underexposure
or are tinged with green.
Optimum value for Clamp Position adjustment
When black parts have no detail due to underexposure (blackout)
´ Value that causes least blackout is the optimum.
When black parts are tinged with green
´ Value that cancels the greenishness without causing blackout is the optimum.
1:1 Pixel Mode
Adjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
• Select On when you would like to replay 1920 × 1080 input signal.
• Applicable input signal;
1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i
• Select Off when ²ickering is shown around the image.
• H-Size and V-Size cannot be adjusted when On is selected.
Off
On
1:1 Pixel Mode
(2k1k)
(For 2k1k signals)
When the input signal is a 2k1k signal (2048 × 1080 / 24p, 2048 × 1080 / 24sF), the display size
is adjusted as follows.
Off
On (Left)
On (Center)
On (Right)
Note:
2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed.
Adjusting Pos./Size
While the Pos./Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
(
) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Helpful Hint (
/
Normalise
Normalisation)