Panasonic TH32LHD7UXK TH32LHD7UXK User Guide - Page 10

Pc Input Terminals Connection

Get Panasonic TH32LHD7UXK - 32inch IND LCD TV PDF manuals and user guides View all Panasonic TH32LHD7UXK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Connections PC Input Terminals connection COMPUTER AUDIO PC IN Conversion adapter (if necessary) TH-32LHD7 Less than 3" 15/16 (10 cm) Ferrite core (large size) (supplied) D-sub 15p RGB PC cable Less than 3" 15/16 (10 cm) Ferrite core (Small size) (supplied) Less than 3" 15/16 (10 cm) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Installing the ferrite core (Small size) 1 2 3 Open Pull back the tabs (in two places) Installing the ferrite core (Large size) 1 2 3 Open Press the cable through and close Pull back the tabs (in two places) Press the cable through and close Notes: • Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to "NORMAL", and 1,366 × 768 dots when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. • The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. • Some PC models cannot be connected to the set. • There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. • The computer shown in the illustration is for example purposes only. • Additional equipment and cables shown are not supplied with this set. • Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. Signal Names for D-sub 15P Connector 11 12 13 14 15 6 7 8 9 10 12345 Pin No. 1 2 3 4 Pin Layout for PC Input 5 Terminal Signal Name R (PR/CR) G (Y) B (PB/CB) GND (Ground) GND (Ground) Pin No. 6 7 8 9 10 Signal Name GND (Ground) GND (Ground) GND (Ground) NC (not connected) GND (Ground) Pin No. 11 12 13 14 15 Signal Name GND (Ground) SDA HD/SYNC VD SCL 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
10
Connections
PC Input Terminals connection
Notes:
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
• The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to “NORMAL”, and 1,366 × 768
dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible
to show
fi
ne detail with suf
fi
cient clarity.
• The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you
will need to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speci
fi
ed
frequency range.
Signal Names for D-sub 15P Connector
Pin Layout for PC Input
Terminal
AUDIO
PC IN
COMPUTER
Conversion adapter
(if necessary)
D-sub 15p
RGB
PC cable
Ferrite core
(Small size)
(supplied)
Less than
3"
15
/
16
(10 cm)
Stereo plug
Audio
Connect a cable which matches
the audio output terminal on the computer.
1
2
3
1
2
3
Installing the ferrite core
(Small size)
Installing the ferrite core
(Large size)
Pull back the tabs
(in two places)
Open
Pull back the tabs
(in two places)
Open
Press the cable
through and close
Press the cable
through and close
1
6
7
8
3
9
4
5
10
15
14
13
12
11
2
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
R (P
R
/C
R
)
6
GND (Ground)
11
GND (Ground)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (P
B
/C
B
)
8
GND (Ground)
13
HD/SYNC
4
GND (Ground)
9
NC (not connected)
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
Less than
3"
15
/
16
(10 cm)
Less than
3"
15
/
16
(10 cm)
Ferrite core (large size)
(supplied)