Panasonic TH32LHD7UXK TH32LHD7UXK User Guide - Page 9

Connections

Get Panasonic TH32LHD7UXK - 32inch IND LCD TV PDF manuals and user guides View all Panasonic TH32LHD7UXK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 SPEAKERS Terminals (R) R AUDIO L IN VIDEO IN VIDEO OUT S VIDEO IN AV R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT 1 SLOT 2 AUDIO PC IN SERIAL SPEAKERS Terminals (L) AC cord connection (see page 12) 2 - AC cord fixing 1. Open the clamper. 2. I n s e r t t h e A C c o r d and close the clamper securely. 3. Slide up the clamper and fix the AC cord plug securely. When loosen the clamper: Clamper AC cord Note: The power plug in the illustration may not be the type fitted to your set. 4. Insert the point of the fixed clamper into the small hole on the lower right of the back cover as necessary. - Cable fixing bands Secure any excess cables with bands as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: Pull To loosen: Push the catch 1 2 Pull Optional Terminal Board insert Slots (covered) R AUDIO L IN VIDEO IN VIDEO OUT S VIDEO IN AV SLOT1 R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT2 AUDIO PC IN SERIAL From EXTERNAL monitor terminal on Computer (see page 10) From SERIAL Terminal on Computer (see page 11) 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
9
Connections
SERIAL
PC
IN
AUDIO
SLOT1
SLOT2
VIDEO IN
VIDEO OUT
AUDIO
IN
R
L
AV
S VIDEO IN
SLOT 2
SLOT 1
PC
IN
SERIAL
1
2
COMPONENT/RGB IN
P
R
/C
R
/R P
B
/C
B
/B
VD
HD
Y/G
R
AUDIO
L
1
2
1
2
SPEAKERS
Terminals (R)
SPEAKERS
Terminals (L)
– Cable
fi
xing bands
Secure any excess cables with bands as required.
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
Speakers (Optional accessories)
Pass the attached cable
fi
xing band through the
clip as shown in the
fi
gure.
To secure cables connected to Terminals, wrap the cable
fi
xing band around them
then pass the pointed end through the locking block, as shown in the
fi
gure.
While ensuring there is suf
fi
cient slack in cables to minimize stress (especially
in the power cord),
fi
rmly bind all cables with the supplied
fi
xing band.
From SERIAL Terminal
on Computer
(see page 11)
From EXTERNAL
monitor terminal on
Computer (see page 10)
AC cord connection (see page 12)
To tighten:
To loosen:
Pull
Pull
Push the catch
3.
Slide up the clamper and
fi
x
the AC cord plug securely.
2.
Insert the AC cord
and close the clamper
securely.
1.
Open the clamper.
Clamper
AC cord
Note:
The power plug in the illustration may not be the type
fi
tted to your set.
When loosen
the clamper:
Optional Terminal Board insert Slots (covered)
– AC cord
fi
xing
4.
Insert the point of the
fixed clamper into the
small hole on the lower
right of
the back
cover as
necessary.