Pantech Crux Manual-English - Page 11

Removing The Battery, Charging The Battery - covers

Get Pantech Crux PDF manuals and user guides View all Pantech Crux manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

REMOVING THE BATTERY 1. To remove the battery cover, insert your finger tip into the slot (1), then push down on the top of the battery cover and slide it off (2). 2. Insert your fingernail into the slot and lift the battery from the compartment. 3. Align the cover tabs with the slots on the back of the phone and slide the battery cover onto the unit until it snaps into place. CHARGING THE BATTERY 1. Connect the USB data cable into the cableless wall adapter. 2. Plug the USB data cable into the phone's charging/ data jack (making sure to align the connector as it appears in the image to the right) and the wall adapter end into an electrical outlet. 18 If the battery connector is not properly aligned, damage could occur to the charging connector and the phone may not be charged. 01 Correct Incorrect 02 03 04 Correct Incorrect 05 06 3. To remove the wall charger, unplug the USB data cable from the phone's charging/data jack. 07 • When you charge the battery with the handset 08 powered off, you will see a charging status screen. After charging is completed, the Charge Complete message appears and you cannot operate the phone until it is powered on. To turn your phone on, press and hold the Power Key until your display turns on. • The battery may not be fully charged at the time of purchase. Fully charge the battery before using. • It is more efficient to charge the battery with the handset powered off. • Battery operating time gradually decreases over time. • If the battery fails to perform normally, you may need to replace the battery. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
18
02
03
04
05
06
07
08
01
19
REMOVING THE BATTERY
1.
To remove the battery cover, insert your finger tip
into the slot (1), then push down on the top of the
battery cover and slide it off (2).
2.
Insert your fingernail into the slot and lift the battery
from the compartment.
3.
Align the cover tabs with the slots on the back of the
phone and slide the battery cover onto the unit until
it snaps into place.
CHARGING THE BATTERY
1.
Connect the USB data cable into the cableless wall
adapter.
2.
Plug the USB data cable into the phone’s charging/
data jack (making sure to align the connector as
it appears in the image to the right) and the wall
adapter end into an electrical outlet.
If the battery connector is not properly aligned, damage could occur to the charging
connector and the phone may not be charged.
Correct
Correct
Incorrect
Incorrect
3.
To remove the wall charger, unplug the USB data
cable from the phone’s charging/data jack.
•
When you charge the battery with the handset
powered off, you will see a charging status screen.
After charging is completed, the Charge Complete
message appears and you cannot operate the phone
until it is powered on. To turn your phone on, press and
hold the Power Key
until your display turns on.
•
The battery may not be fully charged at the time of
purchase. Fully charge the battery before using.
•
It is more efficient to charge the battery with the
handset powered off.
•
Battery operating time gradually decreases over time.
•
If the battery fails to perform normally, you may need
to replace the battery.