Philips 32PF7321D User manual - Page 11

English Française Español CABLE 75 & Basic connections to the TV Your integrated digital TV automatically decodes and displays the four basic DTV picture resolution standards. - SDTV (Standard Definition TV) are broadcast as 480i (480-line interlaced) or 480p (480-line progressive scan) video. - HDTV (High-Definition TV) are broadcast either in the 1080i or 720p formats, always with a widescreen picture. Note: Progressive scan video (p) is more like that you see in a movie theater. Images are much more distinct and free of flicker, and motion is smoother. Next to analog NTSC broadcast reception, your TV has an integrated High Definition TV tuner which receives, decodes and displays terrestrial ATSC and unscrambled cable (QAM) signals. HDTV quality is only reproduced when a broadcaster or cable provider broadcasts HDTV signals. CABLE HDMI 1 HDMI 2 75 TO TV OUTPUT 2 IN OUT 3 There are 2 ways to get HDTV content: - via cable, conn us entry05- cvabiale.eapnstenna. Note: This drawing is used wherever you can connect cable or antenna. - Cable TV Connect the cable TV signal to the cable/antenna 75 Ω x jack at the bottom of the TV. See page 8 for details on using Autoprogram to store channels in the TV's memory. Note: this connection will supply stereo sound to the TV if it is being broadcast by the station you are watching. Set-Top Box - Cable box with rf in/out • Connect the incoming cable TV signal to the cable in jack 1 on the back of the cable box. • Connect a coaxial cable (not supplied) from the to tv jack on the back of the cable box to the cable/antenna 75 Ω x jack 2 at the bottom of the TV. Note: Your cable box may have a different label for the to tv jack, such as output or out. • Set the output ch switch 3 of the cable box to ch 3 or 4 (whichever is correct for your cable box), then tune the TV to the corresponding channel. Once tuned, change channels at the cable box, not the TV. AV1 : L + R + VIDEO CABLE 1 Note: This connection will not supply stereo sound to the TV. The reason is that the RF output on a cable box - labeled to tv, out or output for example - will not send a stereo signal to the tuner (VHF/UHF) input on a TV. 4 2 SIGNAL SPLITTER 3 conn us entry05 cable RF.eps - Cable box with A/V outputs • Connect the incoming cable TV signal 1 to a signal splitter (not supplied). The signal splitter enables you to avoid having to use the TO TV jack on the OUT IN back of the cable box. This jack will not supply stereo sound to the TV. Note: Your cable box may have a different label for the to tv jack, such as Set-Top Box output or out. • Connect a coaxial cable (not supplied) to a connector on the signal splitter and to the cable/antenna 75 Ω x jack 2 on the TV. • Connect another coaxial cable (not supplied) to a connector on the signal Watching Cable TV programs that don't file : conn us entry05 cable AV.eps splitter and to the cable in jack 3 on the back of the cable box. require the cable box • Connect A/V cables (not supplied) to the video and audio l and r outputs Since you've connected the cable TV signal directly to the TV's tuner, you can also watch the unscrambled programs by simply tuning to the desired channel. You must first use Autoprogram, however, to store channels in the TV's memory. See page 8. Note: This connection will supply stereo sound to on the back of the cable box and to the AV2 video (labeled video) and audio (labeled L and R) jacks 4 on the back of the TV. • To view programs from your cable box, first press the av+ button on the remote control. • Press the cursor down or up buttons until the AV2 signal source is selected. • Press the OK button to confirm your selection. The AV2 input source becomes current for the viewing of cable TV programs through your cable box. the TV if it is being broadcast by the station you are Note: If your cable box Audio/Video outputs will not supply video and stereo audio to watching. the TV, you will need to make the connection shown above in the example "Cable box with RF IN/OUT".