Philips 51PP9363H Quick start guide - Page 2

HOOKING UP THE TV ANTENNA TV This connection WILL supply stereo sound to the TV. 1 Connect the antenna signal to the ANTENNA IN 75Ω jack on the back of the TV. NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on pages 4 and 5 of this guide. Set TUNER MODE to the ANTENNA option. Run AUTO PROGRAM to store all available cable channels in the TV's memory. Antenna Signal ANTENNA IN 75Ω 1 Back of TV DVI INPUT-AV 1 VIDEO S-VIDEO L L AUDIO R OUTPUT Y Pb Pr INPUT-AV 2 VIDEO S-VIDEO L L AUDIO R HD INPUT-AV 5 HD INPUT-AV 4 G/Y R/Pr B/Pb V L SYNC AUDIO H R L AUDIO R POWER TV SWAP VCR PIP CH ACC ACTIVE CONTROL FREEZE DN UP SOUND PICTURE STATUS/ EXIT MENU/ SELECT OPERATING THE TELEVISION AND REMOTE CONTROL TELEVISION USING THE TV BUTTONS Should your remote control be lost or broken, you can still change some of the basic picture and sound settings with the buttons on the TV. Follow the steps below to familiarize yourself with the functions of the TV buttons. 1 Press POWER/STANDBY to turn the TV on (or off). Allow about 10 seconds for the TV to power on. 2 Press the VOL(ume) + or - buttons to decrease or increase the sound level. Press the VOLUME + and - buttons simultaneously to display the on-screen menu. After the menu appears, use these buttons to enter submenus and make selections or adjustments. (Use the CHANNEL buttons to move up and down in the menu or submenus.) Press both VOLUME buttons simultaneously to back out of the on-screen menus. 3 Press SOURCE SELECT to choose from among the signal inputs you have connected to the TV. 4 Press the CHANNEL buttons to select TV channels. VOLUME - A + A MENU CHANNEL ?> SOURCE SELECT VOLUME - A + A MENU CHANNEL ?> SOURCE SELECT Remote Sensor Window Power Standby Button HELPFUL HINT You can press any of the buttons on the front of the TV to turn the TV on, but you must press the Power/Standby button to turn the set off. REMOTE CONTROL INSTALLING BATTERIES T o load the supplied batteries into the remote, follow these steps. 1 Gently press and hold the indentation on the back of the remote and slide the battery cover off the remote. 2 Place the two "AA" size batteries in the remote's battery case. Ensure that the (+) and (-) ends of the batteries line up correctly with the (+) and (-) inside the case. 3 Slide the battery cover back into place. POINTING THE REMOTE Press the TV mode button on the remote to ensure that the remote sends its commands to the TV. When operating the remote control, point the remote toward the remote sensor window on the TV. c CHECK IT OUT You can set up your TV remote control to work with accessory devices such as VCRs, DVD players, and cable converter boxes. See pages 18-23 in the Directions for Use manual. POWER TV VCR ACC OTKV SWAP VCR PIP CH DDNN ACC ACCOTNIVTEROL FREEZE UUPP PICTURE SOUND MESNELUE/CT TV MODE STATEUXSIT/ MUTE CH BVOL utton 3 1 2 6 4 5 8 9 7 TV/VCRAA//CCHH 0 SCUCRF PIP POSITION 2 BATTERY USAGE CAUTION To prevent battery leakage that may result in injury to you or damage to the remote control: • Install ALL batteries correctly, + and -, as marked on the unit. • Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.) • Remove batteries when the remote control is not used for a long time. Do not take apart, heat, or put batteries in fire. HELPFUL HINTS • Be sure to point the remote toward the sensor window on the TV or accessory device you wish to operate. • Press the correct mode button for the device: TV, VCR, ACC (for accessories other than VCRs). • Be within about 30 feet (10 meters) of the TV or accessory device you wish to operate. • Avoid dropping the remote on hard surfaces. • Do not use harsh chemicals to clean the remote. Use only a soft, lightly moistened cloth.