Philips 51PP9363H Quick start guide - Page 8

ADJUSTING THE MANUAL CONVERGE CONTROLS CONVERGE RED/BLUE Bumps and vibrations, moving the set, or the presence of magnetic fields (from speakers, for example) can cause the beams of light coming from the TV's three color projection tubes to become misaligned. The result is color haloes, or outlines, around portions of the picture. If your picture looks okay, there's no need to adjust convergence. If your TV's picture has the color haloes, however, refer to the chart to the right for guidance as to which convergence controls to use, then follow the simple steps below. 1 Press the MENU/SELECT button. The menu appears. Press the CURSOR RING RIGHT to enter the PICTURE submenu. Then press the CURSOR RING DOWN until MANUAL CONVERGE is highlighted. 2 Press the CURSOR RING RIGHT to enter the MANUAL CONVERGE submenu. If you want to adjust the Red Convergence, press the CURSOR RING RIGHT to enter the adjust mode. If you want to adjust the Blue Convergence, press the CURSOR RING DOWN to highlight CONVERGE BLUE, then press the CURSOR RING RIGHT to enter adjust mode. 3 In adjust mode, press the CURSOR RING RIGHT, LEFT, UP, or DOWN to adjust the cross hair until the color halo around it is gone. (The adjustment is automatically saved in the TV's memory.) To return to the MANUAL CONVERGE menu, press the MENU/SELECT button. To exit the on-screen display, press the STATUS/EXIT button. Screen Appearance Actions Various parts of the picture have red haloes. Adjust the CONVERGE RED control. Then if any red haloes remain, adjust the MULTIPOINT RED control. Various parts of the picture have blue haloes. Adjust the CONVERGE BLUE control. Then if any blue haloes remain adjust the MULTIPOINT BLUE control. PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT POWER TV SWAP SOUND VCR PIP CH DN UP ACC ACTIVE CONTROL FREEZE 2,3 PICTURE STATUS/ EXIT MENU/ SELECT MUTE VOL 1 CH 123 456 789 TV/VCR A/CH 0 SURF Converge Red Converge Red MULTIPOINT RED/BLUE T he Multipoint Red/Blue Convergence controls enable you to adjust the convergence at specific points on the TV screen. NOTE: The on-screen display will leave the screen after 20 seconds of inactivity. If this happens, simply press the MENU/SELECT button to bring the MANUAL CONVERGE submenu back. 1 Press the MENU/SELECT button. The menu appears. Press the CURSOR RING RIGHT to enter the PICTURE menu. Then press the CURSOR RING DOWN until MANUAL CONVERGE is highlighted. 2 Press the CURSOR RING RIGHT to enter the MANUAL CONVERGE submenu. Press the CURSOR RING DOWN until MULTIPOINT RED or MULTIPOINT BLUE is highlighted. Then press the CURSOR RING LEFT or RIGHT to enter Navigate mode. 3 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to move to a cross hair that has a color outline. Then press the STATUS/EXIT button to enter adjust mode. 4 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to adjust the cross hair image until the color outline is gone. Then press the STATUS/EXIT button to return to NAVIGATE mode. Repeat steps 3 and 4 until all misaligned cross images have been adjusted. 5 After making your adjustments, you must store them in the TV's memory using SAVE MULTIPOINT. NOTE: If you are not satisfied with the adjustments you just made and want to start over, you can use the UNDO MULTIPOINT control. This control allows you to undo the adjustments, but it will work only if you use it before saving. To save your multipoint adjustments, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until SAVE MULTIPOINT is highlighted. Then press the CURSOR RING LEFT or RIGHT to store your adjustments in the TV's memory. OR To undo the multipoint adjustments you just made, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until UNDO MULTIPOINT is highlighted. Press the CURSOR RING LEFT or RIGHT to undo the adjustments. Press the CURSOR RING UP until MULTIPOINT RED or MULTIPOINT BLUE is highlighted. Press the CURSOR RING LEFT or RIGHT to enter Navigate mode. Then Follow steps 3-5 above to make your adjustments again. OR To restore the TV's convergence to factory settings, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until RESTORE FACTORY is highlighted. Then press the CURSOR RING LEFT or RIGHT to restore the TV's convergence to factory settings. 6 Press the STATUS/EXIT button to exit the submenu. PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED L MULTIPOINT BLUE É SAVE MULTIPOINT to Navigate Exit to Adjust L L POWER TV SWAP 3,4 SOUND VCR PIP CH DN UP ACC ACTIVE 2 CONTROL FREEZE PICTURE STATUS/ EXIT MENU/ SELECT to Navigate Exit to Adjust to Adjust Exit to Navigate MUTE 6 VOL CH 1,5 123 456 789 TV/VCR A/CH 0 SURF POSITION PIP to Navigate Exit to Adjust to Adjust Exit to Navigate to Adjust Exit to Navigate PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED L MULTIPOINT BLUE É SAVE MULTIPOINT PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED L MULTIPOINT BLUE SAVE MULTIPOINT SAVE MULTIPOINT PICTURE MANUAL CONVERGE CONVERGE RED CONVERGE BLUE MULTIPOINT RED L MULTIPOINT BLUE SAVE MULTIPOINT STORED HELPFUL HINT If you should experience a power outage before saving your multipoint-convergence settings, your settings will be lost. PICTURE MANUAL CONVERGE CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE L SAVE MULTIPOINT UNDO MULTIPOINT PICTURE MANUAL CONVERGE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT L UNDO MULTIPOINT RESTORE FACTORY OR UNDO MULTIPOINT PICTURE MANUAL CONVERGE CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE L SAVE MULTIPOINT UNDO MULTIPOINT RESTORED OR RESTORE FACTORY PICTURE MANUAL CONVERGE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT L UNDO MULTIPOINT RESTORE FACTORY RESTORED 8