Philips AZ2055 User manual - Page 9

DIGITAL TUNER CD DIGITAL TUNER Tuning to radio stations 1 Press y to on, then press SOURCE to select TUNER. - TU is displayed briefly and then the radio station frequency, waveband and, if programmed, a preset number are shown. (See 4) 2 Press BAND once or more to select your waveband. 3 Press and hold ∞ or § until the frequency in the display starts running. ™ The radio automatically tunes to a station of sufficient reception. Display shows during automatic tuning. ™ If a FM station is received in stereo, is shown. 4 Repeat steps 2-3 if necessary until you find the desired station. • To tune to a weak station, press ∞ or § briefly and repeatedly until you have found optimal reception. Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order of waveband reception strength: FM, followed by AM. Any previous presets e.g. manually programmed will be erased. • Press PROG for 4 seconds or more to activate autostore programming. ™ The display shows AUTO, program blinks, followed by the radio station details when stored. (See 5) After all stations are stored, the first autostore preset station will then automatically play. To listen to a preset or autostore station Press the PRESET (up or down) buttons once or more until the desired preset station is displayed. CD PLAYER Playing a CD This CD player plays Audio Discs including CD-Recordables and CD-Rewritables. To improve radio reception: • For FM, extend, incline and turn the telescopic antenna. Reduce its length if the signal is too strong. • For AM, the set uses a built-in antenna. Direct this antenna by turning the whole set. Programming radio stations You can store up to a total of 30 radio stations in the memory, manually or automatically (Autostore). Manual programming 1 Tune to your desired station (see Tuning to radio stations). 2 Press PROG to activate programming. 3 Press PRESET DOWN/ UP once or more to select a preset number. 4 Press PROG to confirm. 5 Repeat steps 1-4 to store other stations. Note: You can erase a preset station by storing another frequency in its place. 1 Press y to on, then SOURCE to select CD. ™ if no CD is inserted. 2 Insert a CD with the printed side facing up and close the CD door. ™ Display: total number of tracks and playing time. ™ is shown if you have inserted a non-finalized CD-R(W). 3 Press 2; to start playback. ™ if your CD contains non-audio files 4 To pause playback press 2;. Press 2; again to resume play. 5 To stop CD playback, press 9. Note: CD play will also stop when: - the CD door is opened - the CD has reached the end - you select tape or tuner source. CD CASSETTE RECORDER Selecting a different track Reviewing the program • Press ∞ or § on the set, once or repeatedly to In the stop position, press and hold PROG until the select. display shows all your stored track numbers in • In the pause/stop position, press 2; to start sequence. playback. Erasing a program Finding a passage within a track You can erase the program by: 1 Press and hold ∞ or §. • pressing 9 twice ™ The CD is played at high speed and low volume. ™ is displayed briefly and 2 When you recognize the passage you want, release disappears. ∞ or § to resume normal playback. • selecting TAPE or TUNER source. Note: During a CD program or if shuffle/ repeat active, searching is only possible within a track. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROGRAM. shuffle - tracks of the entire CD/ program are played in random order shuffle and repeat all - to repeat the entire CD/ program continuously in random order repeat all - repeats the entire CD/ program repeat (and shuffle repeat) - plays the current (random) track continuously CASSETTE RECORDER Cassette playback 1 Press y to on, then SOURCE to select TAPE. ™ Display: shows throughout tape operation. 2 Insert a cassette and close the door. 3 Press PLAY 2 to start playback. 4 To pause, press PAUSE ;. Press again to resume. 5 Press SEARCH 5 or 6 to fast wind the tape. 6 To stop the tape, press STOP/OPEN 9/. • The keys are automatically released at the end of a tape, except if PAUSE ; has been activated. 1 To select play mode, press MODE once or more. 2 Press 2; to start playback if in the stop position. 3 To select normal playback, press MODE repeatedly until the various modes are no longer displayed. - You can also press 9 to cancel your play mode. Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1 Press ∞ or § on the set to select your desired track number. 2 Press PROG. ™ If you attempt to program without first selecting a track number, is shown. 3 Repeat steps 1-2 to select and store all desired tracks. ™ Display: if you try to program more than 20 tracks.