Philips AZ2780 User manual - Page 18

Troubleshooting

Get Philips AZ2780 PDF manuals and user guides View all Philips AZ2780 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

English AZ 2765 /17 page 18 TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service center. WARNING: Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this would invalidate the warranty. PROBLEM - POSSIBLE CAUSE • REMEDY No sound/power - VOLUME is not adjusted • Adjust the VOLUME - Headphones connected • Disconnect headphones - Power cord not securely connected • Connect AC power cord properly - Batteries dead/ incorrectly inserted • Insert (fresh) batteries correctly Display does not function properly/ No reaction to operation of any of the controls - Electrostatic discharge • Switch off set, disconnect the power plug and reconnect after a few seconds CD playback does not work - CD is badly scratched/ dirty • Replace/ clean CD (see MAINTENANCE) - Laser lens steamed up • Wait until lens has acclimatized The CD skips tracks - CD is damaged or dirty • Replace or clean the CD - SHUFFLE or a program is active • Quit SHUFFLE/PROGRAM mode(s) Poor cassette sound quality - Dust and dirt on the heads, etc. • Clean deck parts etc., see maintenance - Use of incompatible cassette types (METAL or CHROME). • Only use NORMAL (IEC I) for recording. Recording does not work - Cassette tab(s) may be broken • Apply a piece of adhesive tape over the missing tab space. For AZ 2765 model only Remote control does not function properly - Batteries dead/ incorrectly inserted • Insert (fresh) batteries correctly - Distance between the set too large • Reduce the distance Environmental information All unnecessary packaging material has been omitted. The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
English
TROUBLESHOOTING
18
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING:
Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this would
invalidate the warranty.
PROBLEM
– POSSIBLE CAUSE
• REMEDY
No sound/power
–
VOLUME is not adjusted
• Adjust the VOLUME
–
Headphones connected
• Disconnect headphones
–
Power cord not securely connected
• Connect AC power cord properly
–
Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
Display does not function properly/ No
reaction to operation of any of the controls
–
Electrostatic discharge
• Switch off set, disconnect the power plug
and reconnect after a few seconds
CD playback does not work
–
CD is badly scratched/ dirty
• Replace/ clean CD (see
MAINTENANCE
)
–
Laser lens steamed up
• Wait until lens has acclimatized
The CD skips tracks
–
CD is damaged or dirty
• Replace or clean the CD
–
SHUFFLE or a program is active
• Quit SHUFFLE/PROGRAM mode(s)
Poor cassette sound quality
–
Dust and dirt on the heads, etc.
• Clean deck parts etc., see maintenance
–
Use of incompatible cassette types (METAL
or CHROME).
• Only use NORMAL (IEC
I
) for recording.
Recording does not work
–
Cassette tab(s) may be broken
• Apply a piece of adhesive tape over the
missing tab space.
For AZ 2765 model only
Remote control does not function properly
–
Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
–
Distance between the set too large
• Reduce the distance
Environmental information
All unnecessary packaging material has been omitted. The packaging can be easily separated into
three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a specialized
company. Please observe the local regulations regarding the disposal of packing
materials, dead batteries and old equipment.
AZ 2765 /17
page
18