Pioneer AVH-P7500DVD Owner's Manual - Page 24

Opening and closing the, LCD panel, Basic Operations

Get Pioneer AVH-P7500DVD PDF manuals and user guides View all Pioneer AVH-P7500DVD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Section 04 Basic Operations Note If you do not operate the function within about 30 seconds, the display is automatically returned to the playback display. Operating the menu by using the joystick You can also perform most of the menu items by using the joystick. ! Switch the remote control operation mode to AVH to operate the menu by using the joystick on the remote control. (Refer to page 18.) 1 Click the joystick during display of each source to display MENU. MENU appears on the display. 2 Move the joystick up or down and then click it to display the function names you want to operate. # To go to the next group of function names, move the joystick to NEXT and click it. # To return to the previous group of function names, move the joystick to PREV and click it. 3 Press BAND/ESC to return to the display of each source. # You can return to the previous display by pressing BACK. Opening and closing the LCD panel The LCD panel will be opened or closed automatically with the turning of the ignition switch on or off. You can turn off the automatic close/open function. (Refer to page 92.) ! The automatic close/open function will op- erate the display as follows.  When the ignition switch is turned OFF while the LCD panel is opened, the LCD panel will close after six seconds.  When the ignition switch is turned ON again (or turned to ACC), the LCD panel will be opened automatically.  Removing or attaching the front panel will automatically close or open the LCD panel. (Refer to page 27.) ! When the ignition switch is turned OFF after the LCD panel has been closed, turning the ignition switch ON again (or turning it to ACC) will not open the LCD panel. In this case, press OPEN/CLOSE to open the LCD panel. ! When closing the LCD panel, check to make sure that it has closed completely. If the LCD panel has stopped halfway, leaving it like this could result in damage. % Press OPEN/CLOSE to open the LCD panel. # To close the LCD panel, press OPEN/CLOSE again. Adjusting the LCD panel angle Important ! If you can hear the LCD panel knocking against your vehicles console or dashboard, press ANGLE () to move the LCD panel a little forward. ! When adjusting the LCD panel angle, be sure to press ANGLE (+/). Forcibly adjusting the LCD panel by hand may damage it. % Press ANGLE (+/) to adjust the LCD panel to an easily viewable angle. The LCD panel angle continues changing as long as you press ANGLE (+/) and hold. 24 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Note
If you do not operate the function within about 30
seconds, the display is automatically returned to
the playback display.
Operating the menu by using the
joystick
You can also perform most of the menu items
by using the joystick.
!
Switch the remote control operation mode
to
AVH
to operate the menu by using the
joystick on the remote control. (Refer to
page 18.)
1
Click the joystick during display of each
source to display MENU.
MENU
appears on the display.
2
Move the joystick up or down and then
click it to display the function names you
want to operate.
#
To go to the next group of function names,
move the joystick to
NEXT
and click it.
#
To return to the previous group of function
names, move the joystick to
PREV
and click it.
3
Press BAND/ESC to return to the display
of each source.
#
You can return to the previous display by
pressing
BACK
.
Opening and closing the
LCD panel
The LCD panel will be opened or closed auto-
matically with the turning of the ignition
switch on or off. You can turn off the automatic
close/open function. (Refer to page 92.)
!
The automatic close/open function will op-
erate the display as follows.
µ
When the ignition switch is turned OFF
while the LCD panel is opened, the LCD
panel will close after six seconds.
µ
When the ignition switch is turned ON
again (or turned to ACC), the LCD panel
will be opened automatically.
µ
Removing or attaching the front panel
will automatically close or open the LCD
panel. (Refer to page 27.)
!
When the ignition switch is turned OFF
after the LCD panel has been closed, turn-
ing the ignition switch ON again (or turning
it to ACC) will not open the LCD panel. In
this case, press
OPEN/CLOSE
to open the
LCD panel.
!
When closing the LCD panel, check to
make sure that it has closed completely. If
the LCD panel has stopped halfway, leaving
it like this could result in damage.
%
Press OPEN/CLOSE to open the LCD
panel.
#
To close the LCD panel, press
OPEN/CLOSE
again.
Adjusting the LCD panel angle
Important
!
If you can hear the LCD panel knocking
against your vehicle
±
s console or dashboard,
press
ANGLE (
²
)
to move the LCD panel a lit-
tle forward.
!
When adjusting the LCD panel angle, be sure
to press
ANGLE (+/
²
)
. Forcibly adjusting the
LCD panel by hand may damage it.
%
Press ANGLE (+/
²
) to adjust the LCD
panel to an easily viewable angle.
The LCD panel angle continues changing as
long as you press
ANGLE (+/
²
)
and hold.
Basic Operations
En
24
Section
04