Pioneer DEH-2400UB Owner's Manual - Page 5

Operating this unit Operating this unit Section 02 English Selecting a source 1 Press SRC/OFF to cycle between: TUNER (tuner)-CD (built-in CD player)-USB (USB)/iPod (iPod)-AUX (AUX) Adjusting the volume 1 Turn M.C. to adjust the volume. WARNING ! Keep the battery out of the reach of children. Should the battery be swallowed, consult a doctor immediately. ! Batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like. CAUTION For safety reasons, park your vehicle when removing the front panel. Note When this unit's blue/white lead is connected to the vehicle's auto-antenna relay control terminal, the vehicle's antenna extends when this unit's source is turned on. To retract the antenna, turn the source off. Use and care of the remote control Using the remote control 1 Point the remote control in the direction of the front panel to operate. When using for the first time, pull out the film protruding from the tray. Replacing the battery 1 Slide the tray out on the back of the remote control. 2 Insert the battery with the plus (+) and minus (-) poles aligned properly. CAUTION ! Use one CR2025 (3 V) lithium battery. ! Remove the battery if the remote control is not used for a month or longer. ! There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. ! Do not handle the battery with metallic tools. ! Do not store the battery with metallic objects. ! If the battery leaks, wipe the remote control completely clean and install a new battery. ! When disposing of used batteries, comply with governmental regulations or environmental public institutions' rules that apply in your country/area. ! "Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/ perchlorate. (Applicable to California, U.S.A.)" Important ! Do not store the remote control in high temperatures or direct sunlight. ! The remote control may not function properly in direct sunlight. ! Do not let the remote control fall onto the floor, where it may become jammed under the brake or accelerator pedal. Menu operations identical for set up menu/function settings/audio adjustments/ initial settings/lists Returning to the previous display Returning to the previous list (the folder one level higher) 1 Press . Returning to the ordinary display Canceling the initial setting menu/set up menu 1 Press BAND/ . Returning to the ordinary display from the list 1 Press BAND/ . Tuner Basic operations Selecting a band 1 Press BAND/ until the desired band (F1, F2, F3 for FM or AM) is displayed. Recalling preset stations 1 Press c or d. ! If MAN (manual tuning) is selected in SEEK, you cannot recall preset stations. You need to select PCH (preset channel) in SEEK. For details about the settings, refer to SEEK (left/right key setting) on the next page. Manual tuning (step by step) 1 Press c or d. ! If PCH (preset channel) is selected in SEEK, you cannot tune up or down manually. You need to select MAN (manual tuning) in SEEK. For details about the settings, refer to SEEK (left/right key setting) on the next page. Seeking 1 Press and hold c or d, and then release. You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d. Storing and recalling stations for each band Using preset tuning buttons 1 When you find a station that you want to store in memory, press one of the preset tuning buttons (1 to 6) and hold until the preset number stops flashing. 2 Press one of the preset tuning buttons (1 to 6) to select the desired station. Switching the display Selecting the desired text information 1 Press . Program service name/frequency-song title/ artist name-entertainment-frequency ! Depending on the band, text information can be changed. ! Text information items that can be changed depend on the area. Function settings 1 Press M.C. to display the main menu. En 5