Pioneer DEH-P4100 Operation Manual - Page 62

Connecting the units, English - wiring

Get Pioneer DEH-P4100 PDF manuals and user guides View all Pioneer DEH-P4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

( Connecting the units ) ( English) aNote • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch. t'ed cable must be wired to the terminal that can detect the operation of the ignition key. Other·wise. battery drain may result. ACC position No ACC position • Use this unit In other than the following conditions could result in fire or malfunction, - Vehicles with a 12·volt battery and negative grounding, -Speakers with 50 W (output value) and 4 ohm to 8 ohm (Impedance value). • To prevent shod·circult. overheating or malfunction. be sure to follow the directions below. - Disconnect the negative terminal of the battery before installation, -Secure the wiring with cable clamps or adheSive tape. To protect the wiring. wrap adheSive tape around them where they lie against metal parts, - Place all cables away from moving parts. such as gear shift and seat rails. - Place all cables away from hot places. such as near the heater outlet. - Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. -Cover any disconnected cable connectors With insulating tape. - Do not shorten any cables. - Never cut the insulation of the power cable of this unit in order to share the power to other eqUipment. Current capacity of the cable is limited. - Use a fuse of the rating prescribed. - Never wire the speaker negative cable directly to ground, - Never band together multiple speaker's negative cables. • Control signal is output through blue/white cable when this unit is powered on, Connect it to an external power amp's system remote control or the vehicle's auto,antenna relay control ter'minal (max. 300 mA. 12 V DC). If the vehicle is equipped with a glass antenna. connect it to the antenna booster power supply terminal. • Never connect blue/white cable to external power amp's power terminal, Also. never connect It to the power terminal of the auto antenna, Otherwise. battery drain or malfunction may resu It. • Ip·BUS connectors are color·coded. Be sure to connect connectors of the same color. • Black cable is ground. This cable and other product's ground cable (especially. high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached,

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
)
(
Connecting the units
(
English)
aNote
•
When
this
unit
is installed in a vehicle
without
ACC (accessory) position on the ignition switch.
t'ed
cable
must
be wired to the
terminal
that
can
detect
the operation of the ignition
key.
Other·wise.
battery
drain may result.
•
Use this
unit
In
other
than the
following
conditions
could result in fire
or
malfunction,
-
Vehicles
with
a 12·volt
battery
and negative
grounding,
-Speakers
with
50
W
(output
value) and 4
ohm
to 8
ohm
(Impedance value).
•
To
prevent
shod·circult.
overheating
or
malfunction.
be sure to follow the
directions
below.
-
Disconnect
the negative terminal of the
battery before installation,
-Secure
the
wiring
with
cable
clamps
or
adheSive tape.
To
protect the wiring.
wrap
adheSive tape around
them
where they lie
against metal parts,
-
Place all cables away
from
moving parts.
such
as
gear
shift
and seat rails.
-
Place all cables away
from
hot places. such
as
near the heater outlet.
-
Do not pass the yellow cable
through
a hole
into the engine
compartment
to
connect
to a
battery.
-Cover
any
disconnected
cable
connectors
With insulating tape.
-
Do not shorten any cables.
-
Never
cut
the insulation of the power cable of
this
unit
in
order
to share the power to
other
eqUipment.
Current
capacity
of the cable is
limited.
-
Use a fuse of the rating prescribed.
-
Never wire the speaker negative cable directly
to ground,
-
Never band
together
multiple
speaker's
negative cables.
•
Control signal
is
output
through
blue/white
cable
when
this
unit
is powered on,
Connect
it to an
external power
amp's
system remote control
or
the vehicle's
auto,antenna
relay
control
ter'minal
(max. 300
mA.
12
V DC). If the vehicle is
equipped
with
a glass antenna.
connect
it to the
antenna
booster power supply terminal.
•
Never
connect
blue/white
cable to external
power
amp's
power
terminal, Also. never
connect
It
to the
power
terminal
of
the
auto antenna,
Otherwise.
battery
drain
or
malfunction
may
resuIt.
•
Ip·BUS
connectors
are color·coded. Be sure to
connect
connectors
of the same color.
•
Black cable is ground. This cable and
other
product's
ground
cable (especially.
high-current
products
such
as
power amp)
must
be wired
separately. Otherwise, fire or
malfunction
may
result if they are accidentally detached,
No ACC position
ACC position