Pioneer DEH-P5100UB Installation Manual - Page 1

CD RECEIVER AUTORADIO CD RADIO CD DEH-P5100UB Installation Manual Manuel d'installation Manual de instalación Printed in Thailand Imprimé en Thaïlande UC Installation Note • Check all connections and systems before final installation. • Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions. • Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle. • Do not install this unit where: - it may interfere with operation of the vehicle. - it may cause injury to a passenger as a result of a sudden stop. • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. • Optimum performance is obtained when the unit is installed at an angle of less than 60°. 60° English 2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. Dashboard Mounting sleeve 182 53 3. Install the unit. • Use commercially available parts when installing. Nut Firewall or metal support Screw Metal strap DIN Front/Rear-mount This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods. DIN Front-mount Installation with metal strap and screws 1. Insert the mounting sleeve into the dashboard. • When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behind the unit, use factory supplied mounting sleeve. Screw (M4˜8) • Make sure that the unit is installed securely in place. Unstable installation may cause this unit to malfunction, such as sound skip. Removing the Unit 1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring Installation 2. Insert the supplied extraction keys into both sides of the unit until they click into place. English 3. Tighten two screws on each side. • Use either truss screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket. Screw 3. Pull the unit out of the dashboard. DIN Rear-mount 1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring Dashboard or Console Factory radio mounting bracket Fastening the front panel If you do not plan to detach the front panel, the front panel can be fastened with supplied screw. Screw 2. Determine the appropriate position where the holes on the bracket and the side of the unit match. Connecting the unit English Note • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result. OF OF F ACC O F O





N STAR N STAR T T ACC position





No ACC position • Use this unit in other than the following conditions could result in fire or malfunction. - Vehicles with a 12-volt battery and negative grounding. - Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value). • To prevent short-circuit, overheating or malfunction, be sure to follow the directions below. - Disconnect the negative terminal of the battery before installation. - Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. - Place all cables away from moving parts, such as gear shift and seat rails. - Place all cables away from hot places, such as near the heater outlet. - Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. - Cover any disconnected cable connectors with insulating tape. - Do not shorten any cables. - Never cut the insulation of the power cable of this unit in order to share the power to other equipment. Current capacity of the cable is limited. - Use a fuse of the rating prescribed. - Never wire the speaker negative cable directly to ground. - Never band together multiple speaker's negative cables. • Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp's system remote control or the vehicle's auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. • Never connect blue/white cable to external power amp's power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result. • IP-BUS connectors are color-coded. Be sure to connect connectors of the same color. • Black cable is ground. This cable and other product's ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.