Pioneer DVR-220-S Service Manual - Page 72
Description of Each Service-mode screen - l firmware
View all Pioneer DVR-220-S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 72 highlights
1 2 3 4 7.1.4 SERVICE MODE For service operations, use the GGF1381 remote control unit for service. The Service-mode screens consist of nine mode screens, which are classified into such rough categories as recording system and VR playback system, and their subscreens. A • How to enter Service mode : Press the ESC then DISP keys in turn while no GUI is displayed. The first screen (version information, etc.) shown below is displayed. • How to exit Service mode : Press the ESC key. • How to advance to the next Service-mode screen : While the first screen is displayed, press directly one of the keys 1-9. For service, use the keys 2, 4 or 5, as shown below. • How to advance to a subscreen within the same Service-mode screen : Press the DIG/ANA key. Pressing the DIG/ANA key repeatedly will change the subscreens within the same Service-mode screen cyclically. B The Service-mode screens to be used for service are as follows: 1 = First screen: Version information, etc. 2 = Second screen: ATA/ATAPI debug screen (Writer data) 4 = Fourth screen: Error log for the VR recording system 5 = Fifth screen: Error log for the VR playback system Note: After entering one of the Service-mode screens, if you wish to shift to another Service-mode screen, exit Service mode first, then reenter Service mode and select your desired Service-mode screen. Description of Each Service-mode screen 1. First screen (version information, etc.) C 1 DVR-220/KU/CA 2 VERSION :1.07 3 SYSCON : RELEASE_44 Rev :1.3599.2.2 4 TUFLCON : 1.22 MASK 5 DRIVE : DVD-RW DVR-107R 1.03 DADL000219WL 6 DEVICE : PRISM-PLUS 7 REGION : 1 8 C 9 FLASH : 32M D $ OK OK OK OK OK : OK (proper combination) NG+ : Version of the tuner microcomputer too advanced NG- : Version of the tuner microcomputer too old (*1) OK : OK (proper drive) NG : NG (improper drive) (*2) OK : OK (proper combination) NG+ : Version of the drive too advanced NG- : Version of the drive too old (*3) OK : Serial No. of the drive already registered NG : Serial No. of the drive not registered (*4) (*1-*4 : Refer to next page) 1 Model name/destination 2 Version of the recorder software 3 Revision No. of the system-control computer software (Edition administration No. [from top to bottom, common software, firmware, application software]) 4 Version No. of the tuner microcomputer, Mask or Flash Result of the combination ckeck with system u-com 5 Information on the built-in drive (Model name, version No., model type, serial No.) 6 Version No. of PRISM 7 Region No. 8 CPRM data (CPRM key No.) 9 FLASH ROM information While the first screen shown above is displayed, press the DIG/ANA key to enter the subscreen shown below. E Note: Each time the DIG/ANA key is pressed, the display changes between the first screen and its subscreen. • Subscreen: Result of error-rate measurement ERR RATE : x.xe-x/ Note: Be sure to start playback after displaying this subscreen to calculate the error rate. During playback in VR mode, the average error rate of the past 10 VOBUs is displayed, and during playback in DVD-Video or Video mode, the average error rate of the past 256 sectors is displayed. During playback in VR mode, the rotation rate of the F drive (/: normal speed, no display = double speed) is also displayed. 72 DVR-220-S 1 2 3 4