Pioneer P90HDD Other Manual - Page 1
Pioneer P90HDD - DEH Radio / CD Manual
UPC - 012562575896
View all Pioneer P90HDD manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
INSTALLATION MANUAL OF OF DEH-P90HDD This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA. Printed in Japan Imprimé au Japon UC N STAR N STAR MANUEL D'INSTALLATION Connecting the Units Note: • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. • To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation. • Refer to the owner's manual for details on connecting the power amp and other units, then make connections correctly. • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. • Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. • Don't pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. • Do not shorten any leads. If you do, the protection circuit may fail to work when it should. • Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. • When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder. • Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common. • If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the connector. • Speakers connected to this unit must be highpower types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged. • When this product's source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp's system remote control or the car's Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal. • When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp's power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction. • To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated. • To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly. • If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig. 1) F ACC O F O T T ACC position No ACC position Fig. 1 • The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. • Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. Auto-equalizing mike jack Pull the auto-equalizing mike jack out of the console box, so that the mike can be plugged in or pulled out even after this unit has been installed. Subwoofer output (SUBWOOFER OUTPUT) Antenna jack 15 cm (5/8 inch) 1 m (3-7/8 inch) This Product Rear output (REAR OUTPUT) 15 cm (5/8 inch) IP-BUS input (Blue) IP-BUS cable Multi-CD player (sold separately) 15 cm (5/8 inch) 1 m (3-7/8 inch) Front output (FRONT OUTPUT) Blue/white To system control terminal of the power amp or Autoantenna relay control terminal (max. 300 mA 12 V DC). Power box Power box cord Install the power box cord securely so that the cord can not be easily pulled out. + Front speaker ≠ Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) System remote control + Front speaker ≠ Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Yellow To terminal always supplied with power regardless of ignition switch position. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Fuse holder Fuse resistor + Front speaker ≠ Left + Rear speaker ≠ White Gray White/black Green Gray/black Violet Green/black Violet/black + Front speaker ≠ Right + Rear speaker ≠ + Rear speaker ≠ + Rear speaker ≠ Orange/white To lighting switch terminal. Black (ground) To vehicle (metal) body. Fuse resistor With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. + Subwoofer ≠ + Subwoofer ≠ Perform these connections when using a different amp (sold separately). Fig. 2