Pioneer PD-R555RW Operating Instructions - Page 109

Cause, Symptom, Remedy

Get Pioneer PD-R555RW PDF manuals and user guides View all Pioneer PD-R555RW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Symptom Cause Remedy Power cannot be turned on. The power cord is unplugged from the power Plug the power cord into a power outlet. outlet. The power was turned off from the component Turn on the component into which the power (stereo amplifier, audio time, etc.) to which it is cord is connected. connected. Playback is impossible. Signal connections are incorrect. Connect properly as indicated in "CONNECTIONS". Recording is impossible. Signal connections are incorrect. Connect properly as indicated in "CONNECTIONS". The CD-R or CD-RW disc in use has been finalized. Use a non-finalized disc. Erase a CD-RW disc. The input selection is incorrect. Select the input connected to the desired source. The REC LEVEL control is set too low. Increase the recording level to an optimum level. Recorded sound is distorted. Signal connections are incorrect. Connect properly as indicated in "CONNECTIONS". There is interference from a TV set. Turn the TV power off or install this unit apart from the TV. The recording level is set too high. Decrease the recording level. The disc is damaged or warped. Use another disc. The disc is extremely dirty. Clean the disc. Remote control operation is The remote control batteries are exhausted. impossible. Replace both of the remote control batteries with new ones. There is an obstacle between the remote control Remove the obstacle. unit and main unit. The remote control unit is operated outside the Operate in the remote controllable range. remote controllable range. Certain tracks are skipped The SKIP PLAY button is set to ON. without being played. Set the SKIP PLAY button to OFF. Skip playback does not occur. The SKIP PLAY button is set to OFF. Set the SKIP PLAY button to ON. A recorded CD-R disc cannot be played on other CD players. ÷ The disc has not been finalized after recording. ÷ When such a disc is loaded in the unit, the CD-R indicator lights up. (Refer to page 16.) ÷ The pickup lens of the other CD player is dirty, impairing its ability to play CD-R discs. ÷ Finalize the disc. (Refer to page 74.) ÷ Try the disc on a different CD player. If it plays OK then get the pickup lens on the original player cleaned. The point-of-sale demonstration is displayed. (Note) The demonstration mode can be initiated by pressing the 4 1 button when the display goes on and the disc is read after turning on the power before timer play starts. (When no disc is provided, press the 4 1 button immediately after "00 00:00" has appeared on the display.) (Activating the demo mode.) To cancel the demonstration mode, press the ¡ ¢ button when the display goes on and the disc is read after turning on the power before timer play starts. (When no disc is provided, press the ¡ ¢ button immediately after "00 00:00" has appeared on the display.) The demonstration will not be displayed any more. (Note) This displays certain characters, like PIONEER, SKIP, and PROGRAM, as a point of sale demonstration. 109 GeE/Int

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
109
<PRE1269>
Cause
The power cord is unplugged from the power
outlet.
The power was turned off from the component
(stereo amplifier, audio time, etc.) to which it is
connected.
Signal connections are incorrect.
Signal connections are incorrect.
The CD-R or CD-RW disc in use has been finalized.
The input selection is incorrect.
The REC LEVEL control is set too low.
Signal connections are incorrect.
There is interference from a TV set.
The recording level is set too high.
The disc is damaged or warped.
The disc is extremely dirty.
The remote control batteries are exhausted.
There is an obstacle between the remote control
unit and main unit.
The remote control unit is operated outside the
remote controllable range.
The SKIP PLAY button is set to ON.
The SKIP PLAY button is set to OFF.
÷
The disc has not been finalized after
recording.
÷
When such a disc is loaded in the unit, the
CD-R indicator lights up. (Refer to page 16.)
÷
The pickup lens of the other
CD
player is
dirty, impairing its ability to play
CD
–
R
discs.
The demonstration mode can be initiated by
pressing the
4
1
button when the display
goes on and the disc is read after turning on the
power before timer play starts. (When no disc is
provided, press the
4
1
button immediately
after
“
00
00:00
”
has appeared on the display.)
(Activating the demo mode.)
Symptom
Power cannot be turned on.
Playback is impossible.
Recording is impossible.
Recorded sound is distorted.
Remote control operation is
impossible.
Certain tracks are skipped
without being played.
Skip playback does not occur.
A recorded CD-R disc cannot
be played on other CD
players.
The point-of-sale
demonstration is displayed.
(Note)
Remedy
Plug the power cord into a power outlet.
Turn on the component into which the power
cord is connected.
Connect properly as indicated in
“
CONNEC-
TIONS
”
.
Connect properly as indicated in
“
CONNEC-
TIONS
”
.
Use a non-finalized disc. Erase a CD-RW disc.
Select the input connected to the desired
source.
Increase the recording level to an optimum
level.
Connect properly as indicated in
“
CONNEC-
TIONS
”
.
Turn the TV power off or install this unit apart
from the TV.
Decrease the recording level.
Use another disc.
Clean the disc.
Replace both of the remote control batteries
with new ones.
Remove the obstacle.
Operate in the remote controllable range.
Set the SKIP PLAY button to OFF.
Set the SKIP PLAY button to ON.
÷
Finalize the disc. (Refer to page 74.)
÷
Try the disc on a different
CD
player. If it
plays
OK
then get the pickup lens on the
original player cleaned.
To cancel the demonstration mode, press the
¡
¢
button when the display goes on and
the disc is read after turning on the power before
timer play starts.
(When no disc is provided,
press the
¡
¢
button immediately after "00
00:00" has appeared on the display.)
The
demonstration will not be displayed any more.
(Note)
This displays certain characters, like PIONEER, SKIP, and PROGRAM, as a point of sale demonstration.
En