Pioneer SC-82 Owner's Manual - Page 76
Zone 3 On/off Or Hdzone On/off.
View all Pioneer SC-82 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 76 highlights
09 Using other functions Using the MULTI-ZONE controls The following steps use the front panel controls to adjust the sub zone volume and select sources. See ZONE 2 remote controls and HDZONE remote controls on page 76 . Important ! ZONE 3 is a function for SC-82 only. It cannot be selected or set with SC-81. - The settings must be changed at ZONE Setup in order to use the HDZONE function (page 98 ). 1 Press the button on the front panel for the zone you want to operate (ZONE 2 ON/OFF, ZONE 3 ON/OFF or HDZONE ON/OFF). The zone switches between on and off each time the button is pressed. The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON. 2 Press MULTI-ZONE CONTROL on the front panel to select the sub zone(s) you want. ! When the receiver is on, make sure that any operations for the sub zone are done while ZONE and your selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone only. If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show in the display. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 SAT/CBL sends the source connected to the SAT/CBL inputs to the primary (ZONE 2) sub room. ! If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on page 52 if you're unsure how to do this). The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not to change stations when recording a radio broadcast. 4 Use the MASTER VOLUME dial to adjust the volume for the sub zone. When Speaker System is set to anything other than ZONE 2, the volume output from the receiver's AUDIO ZONE 2 OUT terminals can be fixed to -40 dB or 0 dB and the volume can be adjusted from the connected amplifier. If you want to adjust the volume from the connected amplifier, see ZONE Setup on page 98 . 5 When you're finished, press MULTI-ZONE CONTROL again to return to the main zone controls. You can also press ZONE 2 ON/OFF, ZONE 3 ON/OFF or HDZONE ON/OFF on the front panel to switch off all output to the sub zone. ! You won't be able to switch the main zone off completely unless you've switched off the MULTI-ZONE control first. ! If you don't plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main rooms so that this receiver is in standby. ZONE 2 remote controls Before operation, hold down Z2 on the remote control (for 1.5 seconds) until the remote control LED flashes one time. The following table shows the possible ZONE 2 remote controls: Button(s) u ALL Input function buttons VOLUME +/- MUTE What it does Switches on/off power in the sub zone. Use to select the input function in the sub zone. Use to select the input function directly (this may not work for some functions) in the sub zone. Use to set the listening volume in the sub zone. Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to -40 dB Fixed or 0 dB Fixed. ZONE 3 remote controls Press the remote control's Z3 to operate the corresponding zone. The following table shows the possible ZONE 3 remote controls: Button(s) u ALL Input function buttons VOLUME +/- MUTE What it does Switches on/off power in the sub zone. Use to select the input function in the sub zone. Use to select the input function directly (this may not work for some functions) in the sub zone. Use to set the listening volume in the sub zone. Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 3 Setup under ZONE Setup is set to -40 dB Fixed or 0 dB Fixed. HDZONE remote controls Before operation, hold down HDZ on the remote control (for 1.5 seconds) until the remote control LED flashes one time. The following table shows the possible HDZONE remote controls: Note When the network function or iPod/USB input is selected using HDZONE, the video converter function is disabled. For that reason, video connected with the video cable or component cable is not output from the HDMI terminal. Also, upscaling of the HDMI input video cannot be performed. To enable the video converter function, turn off HDZONE or set HDZONE to some other input. Button(s) u ALL Input function buttons VOLUME +/- MUTE What it does Switches on/off power in the HDZONE. Use to select the input function in the HDZONE. Use to select the input function directly (this may not work for some functions) in the HDZONE. Use to set the listening volume in the HDZONE. Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). a You can operate this only when Speaker System is set to HDZONE. 76