Pioneer SC-89 Owner's Manual - Page 60

05 Basic playback Playing an MHL-compatible device MHL (Mobile High-definition Link) is an interface standard for transmitting digital signals with mobile devices. MHL can carry high quality multi-channel audio data and 3D/Full-HD video formats. The MHL-compatible device's video signals are output from the TV connected to the receiver, the audio signals are output from the speakers connected to the receiver or TV. 1 Press u STANDBY/ON to switch on the receiver and your TV. See Connecting an MHL-compatible device on page 45. 2 Press MHL on the remote control to switch the receiver to the MHL. 3 Select and play the desired contents on the MHL-compatible device. Notes ! MHL-compatible devices can be operated with the receiver's remote control by pressing the remote control's MHL button, but depending on the MHL-compatible device being used, some buttons may not be operable. ! To playback from a MHL-compatible device connected to the receiver on a TV that is also connected to the receiver, the power to the receiver must be turned on. Enjoy Roku video streaming service Connect the Roku Streaming Stick (optional) to the MHL terminal on the main device to enjoy video streaming. 1 Press u STANDBY/ON to switch on the receiver and your TV. See Connecting an MHL-compatible device on page 45. 2 Press MHL on the remote control to switch the receiver to the MHL. 3 Select the contents you want to play and playback. Note When the Roku Streaming Stick (optional) is connected to the MHL terminal of the receiver and the power of the receiver is turned on for the first time, the settings screen is displayed. You can change settings later (page 110 ). Playing music from a computer SC-89 only Use this function to play digital audio input to the unit's rear panel USB-DAC IN terminal. Important ! When switching this unit's input from USB-DAC to another input, first quit the computer's music playback application, then switch the input. ! The exclusive driver must be installed on the computer in order to play high sound quality files of over 48 kHz/24 bits and DSD files. The driver software is provided on the included CD-ROM. 1 Press u STANDBY/ON to switch on the receiver and your computer. See Using a USB cable to connect to a computer on page 46 . 2 Use ALL c/d to select USB-DAC. You can also use the INPUT SELECTOR dial on the front panel. 3 Begin playback on the computer. Notes ! Output from the OPTICAL OUT terminal is not supported during USB-DAC IN input. ! In addition to LPCM, DSD with DoP transmission is also supported. The supported format is 2.8 MHz, 1 bit. Only two channels, including LPCM, are supported. ! Playback cannot be controlled from this unit during use of this function; use your computer to control playback. ! When disconnecting the USB cable, always stop playback on the computer first. ! Sound may not be produced if your computer does not support USB 2.0 HS. ! This unit does not support use of a USB hub. Always use a USB cable to connect the unit directly to the computer. About playable file formats The USB-DAC function of this receiver supports the following file formats. Note that some file formats are not available for playback although they are listed as playable file formats. Category LPCM DSD LPCM DSDIFF DSF Sampling frequency Quantization bitrate Channel Sampling frequency Quantization bitrate Channel Stream 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz 16 bit, 24 bit, 32 bit 2 ch 2.8 MHz 1 bit 2 ch ! With DSD playback, only the DoP standard is supported. A PC player supporting the DoP standard is required. Only native playback is supported for DSD. ! When Speaker System is set to 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp, the audio signals of DSD files are not output to Speaker B. ! When USB-DAC is selected in the sub zone, DSD files and PCM signals with a sampling frequency of 176.4 kHz cannot be played. 60