Pioneer VSX-1124-K Owner's Manual - Page 100

13 FAQ Symptom Remedy The volume level drops automatically. The temperature within the unit has exceeded the allowable value. Try moving the unit for better ventilation (see Installing the receiver on page 10). Volume seems different when input Set the Channel Level setting to ALL, then adjust the volume of the respective input is switched. sources (see Input Volume Absorber on page 71). When HDZONE is ON, multi-channel When HDZONE is selected in Speaker System and also the same HDMI input is selected audio sources are not output in the for both the main zone and HDZONE, 2-channel PCM audio sources are output from the main zone. main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change the HDZONE input. ADAPTER PORT terminal Symptom Remedy The Bluetooth wireless technology device cannot be connected or operated. Sound from the Bluetooth wireless technology device is not emitted or the sound is interrupted. Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If such an object is near the unit, set the unit far from it. Or, stop using the object emitting the electromagnetic waves. Check that the Bluetooth wireless technology device is not too far from the unit and that obstructions are not set between the Bluetooth wireless technology device and the unit. Set the Bluetooth wireless technology device and the unit so that the distance between them is less than about 10 m (33 ft.) and no obstructions exist between them. Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly connected. The Bluetooth wireless technology device may not be set to the communication mode supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless technology device. Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth wireless technology device. Reset the pairing. Check that the profile is correct. Use a Bluetooth wireless technology device that supports A2DP profile and AVRCP profile. ADT OVERLOAD is displayed on the display. There is a problem in the power supply for the Bluetooth adapter. After turning OFF the power of the receiver, disconnect the Bluetooth adapter and insert the Bluetooth adapter again, then turn ON the power of the receiver. If ADT OVERLOAD is displayed even though the above operation is repeated several times, there is a problem with the receiver or the Bluetooth adapter. Disconnect the power cable and request repair. Video Symptom No image is output when an input is selected. Noisy, intermittent, or distorted picture. The picture's movement is unnatural. Video parameters cannot be used. Remedy Check the video connections of the source component. For HDMI, or when V.CONV is set to OFF and a TV and another component are connected with different cords (in Setting the Video options on page 69), you must connect your TV to this receiver using the same type of video cable as you used to connect your video component. For the component video input, however, signals are only output from the HDMI output, so when using the component video input, set V.CONV to ON. Make sure the input assignment is correct for components connected using component video or HDMI cables (see The Input Setup menu on page 40). Check the video output settings of the source component. Check that the video input you selected on your TV is correct. Some components (such as video game units) have resolutions that may not be converted. If adjusting this receiver's Resolution setting (in Setting the Video options on page 69) and/or the resolution settings on your component or display doesn't work, try switching V.CONV (in Setting the Video options on page 69) to OFF. When the HDMI OUT 1/2 setting of the output parameter function is set to OFF, set it to ON. When the network function or iPod/USB input is selected in HDZONE, video connected with the video cable or component cable is not output from the HDMI terminal. To output video, turn off HDZONE or set HDZONE to some other input (page 72). Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video quality may just be poor (with some video game units, for example). The picture quality may also depend on the settings, etc. of your display device. Switch off the video converter and reconnect the source and display device using the same type of connection (component or composite), then start playback again. When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p, the picture may not be displayed properly for some source materials. In this case, set the resolution to something other than 1080/24p or 4K/24p (page 69). For audio only input (TUNER, CD, and TV), the video parameter function cannot be used. Use for video or input with a GUI display. Cannot be used when the HDZONE is ON. Turn OFF the HDZONE. 100